Epps Manufacturing License

[epps]

Ellwood Epps has secured a manufacturing license which allows us to fabricate barrels for the following guns:

AR-15 – 9mm Luger --- barrel lengths available: 7” and longer
Beretta CX4 Storm – any caliber --- barrel lengths available: 13-1/2” and longer
HK USC -- .45 ACP --- barrel lengths available: approximately 10” and longer

Fabricated barrels can have the muzzles threaded to accept flash hiders or muzzle brakes, based upon customer request.

Under this license, we are able to manufacture any barrel length that is of legal dimensions based upon the restrictions of The Firearms Act.

Please note that we cannot cut down any existing manufactured barrel below minimum legal limits. This means that, for example, we cannot cut a rifle barrel below 18.5 inches, nor can we cut an existing shotgun barrel to 14 inches. We can, however, fabricate barrels of these lengths from new stock.

Prices for all projects are determined on an as-requested basis, due to the availability of materials and the labour requirements for each individual project. Please call in advance for pricing applicable to the job you wish to have done.

 

[coldfire]

good to know thanks, keep up the good work

 

[mildot]

How about 10.5 CQC SCAR barrels?

 

[OneBarfly]

Congrats! Thanks for bringing this capability on. ... how about some pre-fab small ring and large ring mauser barrels in 7.62x39 pretty please

 

[sulisa]

Wow, congrats on the new License! Nicely done, here's hoping for lots of work for Epps!

 

[Can Can]

I foresee quite a few 18.5" 9mm CX4 Storm barrels in your future......

Any idea what it would cost to have one made up?

Paul

 

[aftermidnight]

And 40 S&W barrels too.

 

[newshot]

Does this mean the cost and length of time required to make a 9mm storm into a non-restricted is going to be lower? If so, what are the new specs?

 

[QMaze]

Anyone upgrade their 9mm Storm to 18.5"?

 

[maple_leaf_eh]

Rifle length .45ACP barrels for faux De Lisle carbines?

 

[themarauder]

This means that, for example, we cannot cut a rifle barrel below 18.5 inches, nor can we cut an existing shotgun barrel to 14 inches. We can, however, fabricate barrels of these lengths from new stock.

Oohhhhh Canada. Dur.

Congrats Epps!

 

[Slowbalt]

Great news!

 

[frumpy]

Mossberg barrels under 18.5" should sell like hotcakes. I don't think there are any around under 18.5"

 

[muttley]

I really wish Epps can manufacture AR-180B's someday.

 

[1glock2nv]

I foresee quite a few 18.5" 9mm CX4 Storm barrels in your future......

Any idea what it would cost to have one made up?

Paul

Epps is doing one for me at the moment cost was around 500 for the job, plus the rifle.

 

[j_san]

Nice! keep em coming. Does this license allow you to make other firearm parts?

 

[SCDL]

What kind of rifling are you using?

Materials?

 

[HAZMAT911]

How about short barrel for my CX4 Storm

 

[Rocket Surgery]

Is this the only manufacturing license you hold? I'm just curious because no one makes a 16 inch 870 barrel and that would be barely non-restricted with a butler creek folding stock. Remington iron sights, IC, and a metal that doesn't rust fast would be awesome.

 

[ChiWaWa]

Epps is doing one for me at the moment cost was around 500 for the job, plus the rifle.

So how did it turn out? How does it look? I just emailed them and was told it would be a 4 month waiting period to get this same work done.... thats much to long IMHO and they need the gun the entire time.