Glock 17 MOS Co-Witness Setup

S

sparky660

New member
EE Expired
Rating - 0%
0   0   0
Have any of you find people done a co-witness setup on a Glock? If so what did you do for a combination? I’m looking at the trijicon RMR or the Leupold Deltapoint. When it comes to the iron sights I’m open to suggestions.
 
Not as yet. I am building a G19 that has a ZEV dragonfly slide. After looking a a few Youtube videos I am planning to go with a RMR with Trijicon Night Sight Suppressor Height for co-witness.
 
Let me know how you like it. If I don’t have my setup by then it would be good to know how you like it.
 
I've built a couple RDS clocks; MOS, and milled. I've used RMR, DP Pro, Shield RMS, and Holosun 508T-V2. The DP Pro has a higher base, so you need really tall sights to co-witness with a MOS. The Trijicon suppressor sights won't clear the base and allow for a co-witness with the DP. Blackbox customs stocks Dawson Precision MOS sights of varying heights and I really like them. You'd be good ok with the trijicon suppressor sights with an RMR on a MOS build, but it depends on how high you want the sights into your RDS window. On another note, I've owned RMR'S, a DP Pro, and a Shield RMS (Failed after 100 rounds), but now have a Holosun 508T-V2. It's tits and basically exceeds the RMR in every way.

oKp1O9j.jpg


iCnYsXX.jpg


gvOvb2p.jpg
 
Last edited:
#### Proenneke said:
I've built a couple RDS clocks; MOS, and milled. I've used RMR, DP Pro, Shield RMS, and Holosun 508T-V2. The DP Pro has a higher base, so you need really tall sights to co-witness with a MOS. The Trijicon suppressor sights won't clear the base and allow for a co-witness with the DP. Blackbox customs stocks Dawson Precision MOS sights of varying heights and I really like them. You'd be good ok with the trijicon suppressor sights with an RMR on a MOS build, but it depends on how high you want the sights into your RDS window. On another note, I've owned RMR'S and a DP Pro, but now have a Holosun 508T-V2. It's tits and basically exceeds the RMR in every way.



Great info!! Thanks!
Click to expand...
 
while mine isn't a 17, its a 40.
i went with the Vortex Venom and the Ameriglow suppressor height tritium night sights.
love the set up.

on my M&P i went with the Leopold DeltaPoint and again the suppressor height sights, works great.

i have a fear that eventually i will put together a pistol and the irons will not work to co-witness but so far ive been good with what ive picked up.
 
Mine is a G34 MOS with Trijicon Suppressor height sights. Currently with a Holosun 507C which sits low enough for co-witness. I had a Vortex Venom on it as well, which also worked with Triji Supressor sights. Dot washes out in photo when on front sight.

rdA72CX.jpg


E65Xats.jpg
 
LAV said:
####, does the Holosun 508T sit higher, the same, or lower than the RMR? Thanks.
Click to expand...

I believe the base is about the same height for co-witnessing irons, however the window and housing are slightly taller. Remember there is a a H508T and a HE508T-V2, and now a HE508T-X2 (Different button orientation as a result of the Trijicon lawsuit) I'm referring to the V2 model, which has the square top.

B61nKTt.png
 
Last edited:
You must log in or register to reply here.
Back
Top Bottom