TV-PressPass
CGN Ultra frequent flyer
- Location
- Mountains, Alberta
So I had some questions about my SVT in another thread. I figured why not share the love?
I picked mine up for $300 and was immediately enamored with it.
I noticed right away that the magazine had some odd paint blemish on it. Cosmetics? As far as I was concerned this was a shooter, not a museum display.
That was, until I botched the reassembly after its first serious cleaning. Being inexperienced and in a rush, I tried to use a pair of pliers to compress the finicky recoil spring in order to re-seat the dust cover, and clumsily scratched the stock:
Not pretty. Knowing it was my own stupid fault didn't help.
But that did open the door to a kind of project I'd never done before: refinishing a wood stock. Online research, and consultation with a friend more experienced than I in cabinetry and carpentry, agreed that linseed oil was the best choice for refinishing. From what we could tell, the stock was originally hand shaped and fit, which matches what I understood about the SVT's manufacturing history. So we weren't about to use any power tools in this process...
Here's what we did:
Interestingly, as we sanded away the original finish, marks and stamps that had been previously invisible were revealed. Beyond the obvious identifier on the side of the stock, I found a subtle and detailed 5 stamp on the underside, as well as a few stock repairs and nicks. Perhaps if I were a dedicated collector and researcher there might be more to learn about this particular 1941 rifle, but I'm happy just having it to shoot.
That's it! Slow meticulous work, but immensely satisfying, and a great way to spend an afternoon or two on the porch with a beer and some tools. I'm suddenly eyeing the other wood stocks in my safe, wondering if they wouldn't benefit from a little love too.
Then things went in a different direction...
I got an optic mount and stainless piston parts from Corwin Arms because: why not?
This is a non-gunsmithing (but somewhat finicky) optics mount that doesn't require any permanent modifications or "bubba-ing" of the rifle. I can restore it back to the middle photo in about 5 minutes. The cheek riser is a Tasmanian Tiger wrist office with layers of foam inserts inside and a section of camera case divider velcroe'd onto the top panel!
So far the brass doesn't seem to be impacting the scope and nothings shaken loose! I have a feeling I should be reducing my gas system now though.
That's my story.
I picked mine up for $300 and was immediately enamored with it.
I noticed right away that the magazine had some odd paint blemish on it. Cosmetics? As far as I was concerned this was a shooter, not a museum display.
That was, until I botched the reassembly after its first serious cleaning. Being inexperienced and in a rush, I tried to use a pair of pliers to compress the finicky recoil spring in order to re-seat the dust cover, and clumsily scratched the stock:
Not pretty. Knowing it was my own stupid fault didn't help.
But that did open the door to a kind of project I'd never done before: refinishing a wood stock. Online research, and consultation with a friend more experienced than I in cabinetry and carpentry, agreed that linseed oil was the best choice for refinishing. From what we could tell, the stock was originally hand shaped and fit, which matches what I understood about the SVT's manufacturing history. So we weren't about to use any power tools in this process...
Here's what we did:
- Sand down the existing finish. Start with 80 grit sandpaper, and burn it up taking off the layers of cosmoline and what-have you.
- Follow it up with 120 grit paper, and then end it off with 220 grit to give it a smooth finish. Move with the grain of the wood.
- Wipe and wet the wood. Wait 24 hours
- Give any roughed up areas another pass with the 220. Because the SVT stock is Arctic Birch it's "hairy wood"
- Find somewhere safe for your stock to dry and apply a coat of double boiled linseed oil. I used an old t-shirt, but any soft cloth will help avoid brush marks.
- Repeat till desired darkness. Waiting 24 hours between coats. I took 5 days and applied 4 coats of oil.
Interestingly, as we sanded away the original finish, marks and stamps that had been previously invisible were revealed. Beyond the obvious identifier on the side of the stock, I found a subtle and detailed 5 stamp on the underside, as well as a few stock repairs and nicks. Perhaps if I were a dedicated collector and researcher there might be more to learn about this particular 1941 rifle, but I'm happy just having it to shoot.
That's it! Slow meticulous work, but immensely satisfying, and a great way to spend an afternoon or two on the porch with a beer and some tools. I'm suddenly eyeing the other wood stocks in my safe, wondering if they wouldn't benefit from a little love too.
Then things went in a different direction...
I got an optic mount and stainless piston parts from Corwin Arms because: why not?
This is a non-gunsmithing (but somewhat finicky) optics mount that doesn't require any permanent modifications or "bubba-ing" of the rifle. I can restore it back to the middle photo in about 5 minutes. The cheek riser is a Tasmanian Tiger wrist office with layers of foam inserts inside and a section of camera case divider velcroe'd onto the top panel!
So far the brass doesn't seem to be impacting the scope and nothings shaken loose! I have a feeling I should be reducing my gas system now though.
That's my story.
