IN-STOCK: All-New TYPE 81 SR

[Ustauk]

YouTuber Gnutzguy did a stock installation and test video for the gen 2 stock:

 

[JeffMan]

YouTuber Gnutzguy did a stock installation and test video for the gen 2 stock:

Thanks Ustauk. I actually watched that video last night.

I'm glad Gnutzguy makes these videos.

I'd do the instillation similarly, but I'd probably center punch the stock through the receiver so the bit doesn't walk into the receiver so much.

 

[saltfree]

///

 

[scianna54]

Thanks Ustauk. I actually watched that video last night.

I'm glad Gnutzguy makes these videos.

I'd do the instillation similarly, but I'd probably center punch the stock through the receiver so the bit doesn't walk into the receiver so much.

Throw that thing off a bridge and see if it still holds together, lol.

At this point I will stick to my original stock and just put a screw into the stock (pre drilled of course) as initially suggested here.

I wonder how many people will screw up drilling the holes.

 

[mr52359289]

Throw that thing off a bridge and see if it still holds together, lol.

At this point I will stick to my original stock and just put a screw into the stock (pre drilled of course) as initially suggested here.

I wonder how many people will screw up drilling the holes.

Done the work this afternoon right after received the kits. It's not that difficult, you can't go much wrong angle since the holes on receiver are very tight. All you have to do is drill halfway from both sides and you should be fine.

 

[scianna54]

Done the work this afternoon right after received the kits. It's not that difficult, you can't go much wrong angle since the holes on receiver are very tight. All you have to do is drill halfway from both sides and you should be fine.

Thanks.

 

[Eugene L]

Installed mine , pins were tight , I mixed up some epoxy and filled some of the open spaces on the bottom by the trigger, along the seams and at the back below the dust cover just so there is no open spaces just for that exter strength . Got to do some shooting today first time sence i purchased it at he first of march. Stock seems nice and solid as compared to it breaking when i had it sholdered when i racked the bolt for the first time. I had lots of time to polish the trigger (recomend highly) and other surfaces, I really enjoy this rifle ! now to attach a reduclas overkill scope lol

 

[scianna54]

Installed mine , pins were tight , I mixed up some epoxy and filled some of the open spaces on the bottom by the trigger, along the seams and at the back below the dust cover just so there is no open spaces just for that exter strength . Got to do some shooting today first time sence i purchased it at he first of march. Stock seems nice and solid as compared to it breaking when i had it sholdered when i racked the bolt for the first time. I had lots of time to polish the trigger (recomend highly) and other surfaces, I really enjoy this rifle ! now to attach a reduclas overkill scope lol

Maybe you can show some pictures what you did?

 

[Murray 3-D]

Got my replacement stock. Looks good and comes with the hardware including a drill bit.

I hope someone makes a video on how to install this.

I’m mechanically inclined but I’m not sure how I’d drill a straight hole for the two side pins. Drill press? I don’t have one.

Regardless, I’m not in any hurry and will wait for someone to provide definitive instructions.

Drill halfway from both sides. First drill should be notably undersize.

 

[Eugene L]

Maybe you can show some pictures what you did?

There is lots of vids on doing triggers,watch as many as you can, basiclly you want to mirror polish all contact surfaces in the trigger group ,get rid of casting or machining marks, will slightly reduce pull pressure but mostly gets rid of that metal on metal feel the stock trigger has , alot of vids use dremmel sanding drums and files, dont . i use 400 wet sanding paper to smoothen and polish with those rubber eraser dremmel bits,dont rush .same idea on the carrer contact surfaces where there is machine marks and the bolt cam polish it up. Or get a reptuble gunsmith to do it . I will post pics of the epoxy
good disasemble vid :
https://youtu.be/-7GAM3K8pj4

 

[mkx01]

it would be cool to run the SR with the side rail mounted magnified optic and a rear sight block mounted 45 degree offset red dot
just sayin'

 

[Tactical Imports]

 

[Tactical Imports]

it would be cool to run the SR with the side rail mounted magnified optic and a rear sight block mounted 45 degree offset red dot
just sayin'

We are working on picatinny side-mount for T81 series, hope to have available for the fall

 

[saltfree]

Curious to know if anyone cares to opine on the listed price (sold out) of $899..... Anyone get a notification? https://www.tacticalimports.ca/nonrestricted-firearms-c-1/type-81-sr-p-698.html

 

[Nasa]

odd? I never got an email saying this price was listed, I would have jumped on that!

 

[Goose762]

So what's the ETA on the next batch?

 

[bfiles]

Yes when are more T81 rifles coming!?!?!

 

[Curtton]

I'd no idea the price dropped to $899. im not happy bcos i paid $1500.

 

[SleepingLion]

Did anyone even manage to buy one at that price?

 

[Murray 3-D]

1500 to 899 ? Something tells me they have good reason to believe something bad is coming for the Type 81 politically.