IPSC Production - CZ SP01 Mags

[Musky Hunter]

Which are the best mags available for SP01? Must be IPSC Production legal?

CZ, BE, Tang? Pls advise.

 

[dsynk]

Which are the best mags available for SP01? Must be IPSC Production legal?

CZ, BE, Tang? Pls advise.

I have not used the BE or Tang mags for the SP01, but using factory CZ mags.

I have not had a problem with them yet.

 

[mrclean]

Factory 10s have been working fine for over three years and 15000+rds
If you drop them on hard surfaces alot (indoor matches) the lips might start to flex and give you some failure to extract problems.

 

[Freedom Ventures]

I do sell a lot of Tanfoglio mags to SP-01 shooters. It seems they like the all-steel design opposed to the half plastic design.

 

[Musky Hunter]

any of the mags have base pads? would help for any indoor shooting...

 

[Canuck44]

I found the Tan mags don't work in the SP-01 very well. Best to stick to CZ mags.

Take Care

Bob

 

[Allen Gun Works]

Ryan, do you need 9mm or 40S&W? I will have a bunch of CZ Tac Sport mags hopefully by next weekend. They have the aluminum and rubber base pads on them. Not sure they will fit the SP-01 though. If they are ready next weekend I will be down that way and you could try one.

 

[Musky Hunter]

Just got some new Tangfoglio mags with rubber pads. How do you guys install the pads? Looks like a ##### to take apart and clean if you use the two small screws on the pad only. You have to remove the two small screws to get to the take down pin. Can you just drill a centre hole to get to the take down pin?

 

[Canuck223]

Just got some new Tangfoglio mags with rubber pads. How do you guys install the pads? Looks like a ##### to take apart and clean if you use the two small screws on the pad only. You have to remove the two small screws to get to the take down pin. Can you just drill a centre hole to get to the take down pin?

Check first, as the pads might not be kosher for production.

 

[maurice]

Check first, as the pads might not be kosher for production.

the pads are Legal for production. Slavex has a recipe for making them easy to clean and take apart. I use different screws to make it easier to screw and unscrew.

 

[Musky Hunter]

.....you can buy the CZ mags with basepads.

 

[BCRider]

.....you can buy the CZ mags with basepads.

From who please?

 

[Musky Hunter]

You can get the factory 19 rd mags in the US or sometimes they pop up on the EE. I didn't want to wait so i got the tangfolgio mags.

According to Vince you can have non oem mags that fit the outside dimensions of the original. Here is a picture of the OEM 19 rd mag and tangfoglio mag C003.

factory CZ mag

tang mag

 

[SuperVisoR]

How are the tan mags working for you Musky? Any issues? I need to buy some mags.

 

[SquibLoad]

the CZ 75 SP01 19 rd pinned to 10 factory is the way to go

 

[D_]

the CZ 75 SP01 19 rd is the way to go

Corrected

 

[SuperVisoR]

Any ideas where I can buy these pinned mags?

 

[Slavex]

use epoxy to put the basepads on the mags. then drill a hole in the rubber to facilitate using a punch to take the mags apart.
don't think the Tan rubber bumpers are legal on a CZ mag though.

 

[Musky Hunter]

All the mags work great in my SP-01. The CZ 10/19rd are the mags get if you can find them. I find they load the easiest.

Slavex, I am using the epoxy route....no problems to clean and load. I'm using the Tangfoglio mags and pads.

 

[Slavex]

coold dude.
question for you. using Tan mags in my Tan, slide locked back, insert loaded mag, hard, slide will not go forward automatically. use CZ mags or Baby Eagle mags, and it will. but what about in your CZ??????