Kinetic bullet pullers

[Davidf]

Does anyone know where I could buy replacement aluminum collars for my kinetic bullet puller?

 

[jethunter]

Does anyone know where I could buy replacement aluminum collars for my kinetic bullet puller?

Which manufacturer?

 

[scotteboy]

You can use the shell holders from a reloading press if you have em

 

[Davidf]

I'm not sure. I bought it many years ago. Now the collar I need is completely worn out. No name on. It's green if that helps

 

[Davidf]

You can use the shell holders from a reloading press if you have em

No these are 4 piece green aluminum collars held together with colored elastic bands

 

[scotteboy]

No these are 4 piece green aluminum collars held together with colored elastic bands
[/QUOTE
I'm not familiar with them.
I'm sure someone will though.
Good luck

 

[I Dont Care About You]

I'm not sure. I bought it many years ago. Now the collar I need is completely worn out. No name on. It's green if that helps

Green is RCBS.

I was in the same boat and couldn't find replacement collars so I just bought another puller. They are pretty cheap.

 

[I Dont Care About You]

I googled the collets and came up with two listings on Amazon.

Just the collets - $15
Blue bullet puller w three collets - $11 + $5 shipping

 

[remlin]

New pullers ones on Amazon are $15-50.

Or you can get just collets for same money.

 

[DiMP]

You can use the shell holders from a reloading press if you have em

This works, can confirm

 

[bearhunter]

No these are 4 piece green aluminum collars held together with colored elastic bands

The first thing I do with those pullers is "throw out" the "four piece collars"

They are a pain in the butt.

A shell head holder will fit under the screw on cap just fine, almost as if they were made that way on purpose.

 

[FLHTCUI]

Does anyone know where I could buy replacement aluminum collars for my kinetic bullet puller?

Amazon, bought three dies for $10.00 this past April actually and the price has gone up a couple $$ and of course shipping too.

​

 

[Davidf]

The first thing I do with those pullers is "throw out" the "four piece collars"

They are a pain in the butt.

A shell head holder will fit under the screw on cap just fine, almost as if they were made that way on purpose.

Thank you all!

Here's what I learned;

1. It's cheaper to order a whole new kinetic bullet puller than it is to buy replacement shell holders.

2. You can absolutely use regular shell holders in a kinetic bullet puller.

 

[Geoff B]

I broke the screw-down collar on mine and contacted RCBS about buying a replacement.
They said "No, our products are guaranteed for life. Give me your address and we'll send you a whole new one."
And they did.

 

[mephisto002]

Amazon, bought three dies for $10.00 this past April actually and the price has gone up a couple $$ and of course shipping too.

https://www.amazon.ca/Generic-Aluminum-Different-Expandable-Collets/dp/B07M8KCS6N?sbo=RZvfv//HxDF+O5021pAnSA==​

that's the one I have since at least 10 years, and I am happy with it.

Pulled 30 44magnum yesterday easy.

 

[tbhupe]

RCBS has replaced my puller twice in 45 years, once for the cap and once for the striking face. I bought a second one (on sale) just to have as a back up. If my puller breaks, I hate to put the whole operation on hold while I wait for the replacement.

 

[fingers284]

The shell holder method is actually easier & quicker than using the original collets.

 

[99Solutions]

I had the experience of them sending me replacements free as with others above. Awesome.

 

[PPCLI-Jim]

Will have to try the shell holder method for my rimmed cases.

 

[Suther]

The first thing I do with those pullers is "throw out" the "four piece collars"

They are a pain in the butt.

A shell head holder will fit under the screw on cap just fine, almost as if they were made that way on purpose.

They're awesome for rimmed cases. I haven't used em much on anything without a rim though.