Let's See Your WK!!!
- Thread starter Wolverine .303
- Start date
- Status
Bonjour43ma
CGN frequent flyer
- Location
- GVRD
Yeah that's pretty much the same clearance on the sides as the factory handguard: not much. Looks like there's good clearance at the top, though!
diablo_man
Regular
- Location
- BC
few passes with a sharp file would do that just fine.
They're solid sights and are comparable to the Burris fixed-power prisms. I've shot with it out to 300m on a different rifle and found the BDC in the reticle to be useful. It ended up on the WK because I replaced it with an Elcan, but I think it's suitable for this rifle and will remain there.
Thanks. I'm still deciding. Yours looks nice.
Dave_K
CGN Regular
- Location
- Van isle. B.C.
Everything is in now. Looking into a brake, thinking SBI HexBrake. Maybe a hand stop too. my arms reach the end of the rail very easily.
I think Im gonna do that. I prefer the charging handle on that side. The grip tape thing works for keeping it on that side.
https://imgur.com/a/IYhzt0v
Finally got mine all rigged up!
Hiper fire edt dm trigger
Tna 15" handgaurd
Tna suppressor muzzle break
Nikon 1-4 m tactical
Shot it the first time the other day and other than a few FTF with the hera mags in their first run I didn't have any issues! Severely satisfied!
Finally got mine all rigged up!
Hiper fire edt dm trigger
Tna 15" handgaurd
Tna suppressor muzzle break
Nikon 1-4 m tactical
Shot it the first time the other day and other than a few FTF with the hera mags in their first run I didn't have any issues! Severely satisfied!
HJH
New member
- Location
- Edmonton, Alberta
How difficult was the hand guard to install?
The handgaurd wasn't that bad. I took the advice other people said about heating the screws up before trying to remove them. They were tight but they did not have any loctite on them like the first few rifles apparently did. I re used the factory barrel nut, which was pretty tight underthe hand gaurd so hopefully that doesn't cause any issues (I don't see how it would). I found that the flash hider was much more of a pain to get off. I ended up having to put a pipe wrench on the flash hider which marked it up a bit but it did come off.
HJH
New member
- Location
- Edmonton, Alberta
Thank you.
I've heard that the TNA handgaurd fits more freely then the stock one, can you confirm and what model is that one
iceangler650
Regular
- Location
- Ontario
High # 12××
Got last week.
My first gun like this.
Finish looks good nice looking rifle!
I did the rubber o ring on the lug on upper to snug up the upper and lower was not an issue to me really but I like the result after putting it on.
Have a vortex 4x12x44, Burris Pepr QD mount, mlok bi pod adapter and bipod coming in mail.
Also ordered 120 rounds of 55gr ammo to break in and try a few groups with it.
Like to get a brass deflector and magpul fixed carbine stock as well.
Might change charging handle if an aftermarket one is made or stronger magnet setup.
Cant wait to break it in and try a few groups with it hopefully shoots as good as she looks after I get it sighted in im going to try and call some coyotes in with the Wk with me.
Last edited:
toxic
CGN frequent flyer
Received my WK recently and the first mission was optics. Doubt this setup will remain but RRA Dominator rear sight with a cheap Amazon bought flip up front sight. And to top it off....a knock off Eotech because damn you Amazon. 
First impressions (haven't fired it yet) is that gun seems like a winner. The balance is almost perfect - much better than an XCR with the heavy barrel. There is no play between the upper and the receiver. The stock is not super solid but it should do the job. There are a couple of very minor brass marks on the side of the receiver which I'm sure is from test firing a few rounds before leaving the factory. I do want to find a brass deflector solution for that. Very satisfied initially....now need to get out and shoot it!
First impressions (haven't fired it yet) is that gun seems like a winner. The balance is almost perfect - much better than an XCR with the heavy barrel. There is no play between the upper and the receiver. The stock is not super solid but it should do the job. There are a couple of very minor brass marks on the side of the receiver which I'm sure is from test firing a few rounds before leaving the factory. I do want to find a brass deflector solution for that. Very satisfied initially....now need to get out and shoot it!
Last edited:
HJH
New member
- Location
- Edmonton, Alberta
Not the best picture.
YKBrute
New member
- Location
- Green Bay South, NL
My WK:
Mods:
-TriggerTech Adaptive Trigger
-Kinetic Development Sidelok Universal Scope Riser
-Cheapo Barska fixed 4x scope
-BCM Vertical Grip Mod 3 (M-LOK)
-BCM Mod 0 Pistol Grip
-Magpul MBUS Sights
-Magpul Type 2 M-LOK Covers
-Magpul Extended Mag Release
-Magpul CTR Buttstock
-VG6 Gamma 556 Muzzle Brake
-RWA Bolt Catch/Release
-Gear Dynamics Quick Adjust Sling
Mods:
-TriggerTech Adaptive Trigger
-Kinetic Development Sidelok Universal Scope Riser
-Cheapo Barska fixed 4x scope
-BCM Vertical Grip Mod 3 (M-LOK)
-BCM Mod 0 Pistol Grip
-Magpul MBUS Sights
-Magpul Type 2 M-LOK Covers
-Magpul Extended Mag Release
-Magpul CTR Buttstock
-VG6 Gamma 556 Muzzle Brake
-RWA Bolt Catch/Release
-Gear Dynamics Quick Adjust Sling
iceangler650
Regular
- Location
- Ontario
Set it up with calling coyotes in mind put the crossfire II 4x12x44 seems not bad for entry vortex my first vortex scope have a few nikons.
Hope this scope setup works good for yote hunting...
Might still change stock to fixed carbine and get a sling for walkin and iron setup for it.
Time to get it out and break it in and try a few groups with it.
still needs brass deflector too.
Last edited:
V-Max
CGN Regular
- Location
- Lower Rainland
My WK:
Mods:
-TriggerTech Adaptive Trigger
-Kinetic Development Sidelok Universal Scope Riser
-Cheapo Barska fixed 4x scope
-BCM Vertical Grip Mod 3 (M-LOK)
-BCM Mod 0 Pistol Grip
-Magpul MBUS Sights
-Magpul Type 2 M-LOK Covers
-Magpul Extended Mag Release
-Magpul CTR Buttstock
-VG6 Gamma 556 Muzzle Brake
-RWA Bolt Catch/Release
-Gear Dynamics Quick Adjust Sling
Looks wicked!! Are you happy with the RWA Catch/Release? I'm considering one of those for mine. Looks like a pretty simple install.
uAJollyRogering
CGN Regular
delete. nvm
btabin
CGN frequent flyer
- Location
- Fraser Valley
My WK:
Mods:
-TriggerTech Adaptive Trigger
-Kinetic Development Sidelok Universal Scope Riser
-Cheapo Barska fixed 4x scope
-BCM Vertical Grip Mod 3 (M-LOK)
-BCM Mod 0 Pistol Grip
-Magpul MBUS Sights
-Magpul Type 2 M-LOK Covers
-Magpul Extended Mag Release
-Magpul CTR Buttstock
-VG6 Gamma 556 Muzzle Brake
-RWA Bolt Catch/Release
-Gear Dynamics Quick Adjust Sling
How do you like that BCM Mod 0 pistol grip? I was leaning that way for my WK.
- Status
