Marlin quality !!!!!!!!!!!!!!!!!!

Well, I read the entire press release, twice, and don't see any reference to being made in the USA. They mention Custom Grade, not Custom Shop, which would presumably be in the US.

10/12/2009
The Winchester Model 94™ Returns.

Morgan, Utah – Winchester Repeating Arms is excited to announce the return of the Model 1894 lever action rifle to its line of firearms for 2010. This reintroduction of the most popular hunting rifle in history will be offered in two Limited Edition models that will commemorate the 200th anniversary of Oliver F. Winchester’s birth in New England in 1810. A Model 1894 Custom Grade and Model 1894 High Grade will be offered in 30-30 Winchester caliber.

The Model 1894 began at the workbench of John M. Browning, being the first sporting rifle to use smokeless powder. It has been said that the Model 1894 has taken more deer than any other rifle in the world, and with over six million sold, has become by far, the most popular rifle in history. What better way to welcome back the timeless Winchester® Model 1894 than with a tribute to Oliver F. Winchester.

Model 1894 Custom Grade. Only 500 Custom Grade rifles in sets with the High Grade model will be offered. This rifle will have an exquisite 24” half-round, half-round octagon deeply blued barrel. A buckhorn rear sight is matched with a Marble’s® gold bead front sight. The Custom Grade model has Grade IV/V walnut with a rich, high gloss finish. Deep scroll engraving covers both sides of the blued receiver. An early Winchester Repeating Arms crest graces the left side of the receiver, with the right side bearing the words, “Two Hundred Years, Oliver F. Winchester,” and the dates “1810 – 2010”, in gold. The barrel is deeply polished, with the signature of Oliver F. Winchester in gold on the top of the bolt. “One of Five Hundred” is inscribed in gold on the barrel of the Custom Grade rifle.

Model 1894 High Grade. The Winchester Model 1894 High Grade also honors and commemorates the 200th anniversary of Oliver Fisher Winchester’s birth. This model is deeply embellished with delicate scroll work, with Oliver F. Winchester’s signature in gold on top of the bolt. The left side of the receiver bears an early Winchester Repeating Arms crest. On the right side are the words, “Two Hundred Years, Oliver F. Winchester,” and the dates, “1810—2010.” The fancy Grade II/III walnut stock is enhanced with a high gloss finish and is delicately checkered, complementing the fine embellishments on the silver nitride receiver. The High Grade model is also chambered in the timeless 30-30 Winchester caliber with a deeply blued half-round, half octagon barrel. A buckhorn rear sight is fitted with a Marble’s gold bead front sight. 500 of the High Grade model will be sold as a set with the Custom Grade. The remaining limited quantities will be sold individually.

Delivery of these two commemorative rifles will begin starting in the 2nd quarter of 2010. Both models have 8 round magazine capacity, 42” overall length, 10” rate of twist with average weight at 8 lbs. The Model 1894 Custom Grade rifle has a Suggested Retail of $1,959.00. The Model 1984 High Grade rifle Suggested Retail is $1,469.00.


Clicked on the 94 link, and nothing there either.

The Model 101 shotgun is proudly spoken of as being made in Belgium. :)

Ted
 
Well, if Winchester is being made to Browning standards, whether they're manufactured in Miroku, Japan, or else where, you know you're getting a
quality product. And yes, Browning BLR's were being made in Miroku and probably still are.
 
Well, I read the entire press release, twice, and don't see any reference to being made in the USA. They mention Custom Grade, not Custom Shop, which would presumably be in the US.

Sorry, my bad. Custom Grade not Custom Shop. Custom Shop would probably cost a lot more.

Winchester (the trademark) formerly licensed by U.S. Repeating Arms Company which had the production facilities, is now owned by FN - Herstal which also owns Browning. Herstal Group has manufacturing locations in Belgium, US, Portugal and Japan. Can't find out definitely where the Model 94 is being made now.
 
Last edited:
Sorry, my bad. Custom Grade not Custom Shop. Custom Shop would probably cost a lot more.

Winchester (the trademark) formerly licensed by U.S. Repeating Arms Company which had the production facilities, is now owned by FN - Herstal which also owns Browning. Herstal Group has manufacturing locations in Belgium, US, Portugal and Japan. Can't find out definitely where the Model 94 is being made now.

Looked at one today (94 Sporter) and it's made by Miroku of Japan (not in Miroku, Japan as I stated earlier:redface:, my bad). The balance point of the
Sporter was just ahead of the receiver while the rifle was empty, so loaded it would balance even further forward. But it was still a very nice, slim,
trim package - if a little long for bush work. I also got to handle the 94 Short and it is definitely a very, very nice rifle: well balanced, compact and it
carries very naturally in the hand. Unfortunately, I was never allowed to cycle them, which is about the same as not being allowed to sit in a car you
were looking at buying. So I started looking at some BLR Takedown models and you know, I still love those BLR's. It's not your traditional lever gun,
but with all the cartridges it's offered in and the ability to use spitzer style bullets makes it a very attractive product. Add the takedown feature and
boy it's one hell of a gun!!!
 
Last edited:
I was planning on buying a new guide gun, from everything I read anything post 2007 was pretty much garbage.
A member PM'd me with a 1998 model 1895GG, it was a little more than I wanted to spend, but she's a quality piece!
It was around the same price as a new one, but it's not even broken in yet.
 
My 336bl will extract all unfired brass but will not extract fired brass from winchester, federal and will only extract remmington 125gr fired, they are sending me new extractor to try. The rim of the rem shell is wider that the other 2 this is why they extract ok.
I have read other forums which say they are having no problems with winchester and federal in their 336bl so i hope its just the extractor.

I have cleaned the chamber and the rest of the gun but this made no difference, only rem 125 will extract when fired.

I will not buy Marlin again.
 
My 336bl will extract all unfired brass but will not extract fired brass from winchester, federal and will only extract remmington 125gr fired, they are sending me new extractor to try. The rim of the rem shell is wider that the other 2 this is why they extract ok.
I have read other forums which say they are having no problems with winchester and federal in their 336bl so i hope its just the extractor.

I have cleaned the chamber and the rest of the gun but this made no difference, only rem 125 will extract when fired.

I will not buy Marlin again.

When my 336 was doing that it was a bent extractor, I just pulled it off, bent it back in a bite then reinstalled it and it has been working fine ever since. I'm still pissed about the quality of that gun though. What a mess.
 
When my 336 was doing that it was a bent extractor, I just pulled it off, bent it back in a bite then reinstalled it and it has been working fine ever since. I'm still pissed about the quality of that gun though. What a mess.
how did u get the extrator off?
my 336 did this from day one
:mad:
 
Best built lever action rifles today are the Miroku's, whether they are the Browning version or the Winchester Models 1871, 1886 and 1895.

A lot of people prefer the Browning, as they kept the original half-#### safety. Personally, I believe the Winchester version, which has the tang safety and rebounding hammer is better than the Browning. Comes down to personal choice though. They are both excellent.

Those Miroku Winchester/Brownings are available in cartridges from .270Win on up to .405Win and .45-70.

The Miroku Browning BLR is also an excellent rifle, and available right up to .300WM.



IMHO, if you're looking for a lever action .30-30, just buy an older Winchester or Marlin, or take your chances with these 'Marlingtons'.
 
When my 336 was doing that it was a bent extractor, I just pulled it off, bent it back in a bite then reinstalled it and it has been working fine ever since. I'm still pissed about the quality of that gun though. What a mess.

A bent extractor!!!!!!!!!!!!!!!!!!!!!!! :eek:
 
358 BLR, I agree with you that if Miroku is making Brownings or Winchesters then they should be quality guns. And a BLR in a takedown model - well that's icing on the cake!

I've got two pre 64 Winchesters and a 50's Savage lever. A nice older Marlin in .45/70 and a BLR Takedown in .308 and I'd be set. Though it wouldn't take two much arm twisting to get me to buy a couple of older Winchesters and maybe a Henry.
 
358 BLR, I agree with you that if Miroku is making Brownings or Winchesters then they should be quality guns. And a BLR in a takedown model - well that's icing on the cake!

I've got two pre 64 Winchesters and a 50's Savage lever. A nice older Marlin in .45/70 and a BLR Takedown in .308 and I'd be set. Though it wouldn't take two much arm twisting to get me to buy a couple of older Winchesters and maybe a Henry.
That new Winchester 94 Short is really a very sweet little unit, I just wish they would have let me play with it a little more. If I ever get the urge for a 30/30,
I'll be going back for another look and maybe by then the novelty will have worn off a bit and the price will be a little more reasonable. I think the quality
of these new Winchester 94's is going to rival the pre-64 models. All I can say is that little gun is still stuck in my brain.:HR:
 
Yeah there's something about that '92 Trapper. Don't know if its legal - that barrel seems awfully short.

But if it is...put one of those big John Wayne oversized levers on it and you can pretend to be Chuck Connors in...

'The Rifleman' :p
 
I checked his bio and he was quite the athlete before Hollywood. Said he was only one of twelve men that played both in the Majors and the NBA.

Seriously though we have really hijacked this thread! Apologies to the OP. (but that takedown BLR would be so sweet!)

...off to watch True Grit!
 
It's a 16 inch barrel, how could it not be legal. The OAL can't be less than 28 inches. Take a piece of dental floss, measure the barrel on your computer monitor, that'll give you a relative distance for 16 inches and then use that same piece of string to see if the receiver and buttstock are bigger/smaller.

The barrel on that gun is definitely smaller than the rest of it, making that gun more than 32inches OAL. It can't be restricted.
 
.... I just bought a brand new Marlin 1894C and it works phenomenal. Fit and finish is pretty damn good. No burrs anywhere/ect.

Have yet to have any malfunctions shooting .38 specials, soon to try .357 magnums out in it.

IMG_0020.jpg

IMG_0018.jpg

Just wondering out loud here, but, isn't that scope mounted WAY to far back?

I'd like to see a pic of you shooting that rifle set up like that. How do you hold it without a cheek weld?

I'm just wondering, as a buddy bought an 1895Marlin in 45/70, came with a scope, and it was impossible to shoot well, as you had to have your face off the stock to shoot.
 
It's a 16 inch barrel, how could it not be legal. The OAL can't be less than 28 inches. Take a piece of dental floss, measure the barrel on your computer monitor, that'll give you a relative distance for 16 inches and then use that same piece of string to see if the receiver and buttstock are bigger/smaller.

The barrel on that gun is definitely smaller than the rest of it, making that gun more than 32inches OAL. It can't be restricted.

It's 26" minimum OAL, not 28".
 
Back
Top Bottom