Need help Identifying 303 British Rifle (Pictures)

randal007

New member
Rating - 0%
0   0   0
My grandpa has this rifle he wants me to Identify and restore. I previously did a 303 Ross rifle for him (Thread Here)
I'm hoping some one will be able to tell me what rifle this is and where it came from. If anyone has any knowledge on how to disassemble it would be greatly appreciated.



























 
Look to me like a P14 Enfield. There's likely plenty of websites around which can help id those marks, but I'm sure the resident experts will be along shortly. Google away while you wait. Looks like the barrel is unmolested. If you can't find a P14 stock anywhere, 1917 Enfields (American) can fit in with minor to no extra fitting. Disassembly is easy, around the trigger guard are some screws, undo them and it should pop right out. Good luck on the build
 
Ya i was looking at that but it doesn't have that dimple at the front.

If you take a look on the full sotck P14 example picture in the above link, it also doesn't have the indent you mentioned. My guess is yours is a military stock that was cut down like many others, perhaps to make a bit lighter for a hunter who would be walking around all day.
 
US Model of 1917 rifles (the US version of this rifle in 30-06) had finger grooves cut in the stock about where I believe you guys are talking about. P14s did not.
 
i believe boyds has nice full length stocks and top guards for this. might be a bit harder getting the pieces but ebay, gunshows, or wgp should have the bits.. nice piece of history, it is british marked
 
those are some ###y stocks very well priced as well
i believe boyds has nice full length stocks and top guards for this. might be a bit harder getting the pieces but ebay, gunshows, or wgp should have the bits.. nice piece of history, it is british marked
 
Pattern of 1914 Star (P.-'14*) made by the Remington Eddystone Arsenal in Pennsylvania for the British Army in 1916. This rifle is about halfway through the contract.

In 1926 these rifles were renamed to Rifle Number 3 Mark 1*(E).

Yes, an American Model of 1917 stock can be used; it was an approved Canadian mod during the Second World War.

This rifle has had the Volley Sights removed, which was pretty much standard, sold surplus following WW2.

They have Enfield-rifled barrels, 5 grooves, very deep, same width as the lands: can be very accurate, prefer flatbasd bullets and last halfway to forever.

This was designed as the Pattern of 1913 to be the ultimate perfection of the bolt rifle and it very nearly made it. P-14 in .303 was a wartime expedient, as was the American Model of 1917. MANY parts interchange between the rifles.

The P.-'13/P.-'14/M-1917 was developed in peacetime into the Remington Model 30S, then into the 30 Express, then into the 725 and 720, then into the 721, 722 and finally the 700. In Connecticut, it became the Winchester 54, then the 70..... and thus the direct ancestor of nearly all modern bolt rifles.

It is strongly based on the 95 Mauser, very much beefed-up.

Reliability is extreme.

Grandpa has good taste in rifles.
 
And a bit more. You have a Mk1*. The bolts from the earlier Mk1 will not interchange with the Mk1* Eddystone did not have finger groves. The stock was a "fat boy"
 
And a bit more. You have a Mk1*. The bolts from the earlier Mk1 will not interchange with the Mk1* Eddystone did not have finger groves. The stock was a "fat boy"

& The Winchester & Remington stocks had finger grooves.

Remington P14
newp14.jpg

newp14lhs.jpg
 
This was for a long time the only magnum-length action within the reach of the ordinary man's pocket, and many have been modified to other calibres.

Good luck getting the front sight off to put the upper band back on.
 
Back
Top Bottom