New shotguns, MAG-FED and SHORTIES - NEW PICS

[DOOK]

I thought there was an 18" min barrel length with an overall length of 26" including stock required?

 

[Artie Fufkin]

Much thicker, and heavier. base is now $299, $309 with GR sights.

Savvy viewers will note the chokes are MOD (3 notches)

Were there any problems reported because of the thinner barrels used on first model? I kind of wish I had waited for this new version with better sights.

AF

 

[darkshadow]

I thought there was an 18" min barrel length with an overall length of 26" including stock required?

I think the Minimum barrel length issue was a ruling against dlask based nonsensically on a U.S. law.

This has NO base in Canadian law, this is why we get the 12s and 15's and the 18 was meant for the US>

 

[Canuck223]

I thought there was an 18" min barrel length with an overall length of 26" including stock required?

You can not reduce by cutting any barrel below 18.5 inches. However, the manufacturer can.

You can not reduce by cutting the OAL below 26 inches. However, commercially available replacement stocks are fine. (With some issues with semi-auto's)

 

[simonsez]

You can not reduce by cutting any barrel below 18.5 inches. However, the manufacturer can.

You can not reduce by cutting the OAL below 26 inches. However, commercially available replacement stocks are fine. (With some issues with semi-auto's)

18.5 inches for semi autos, 18 inches for non-semi autos

 

[shawn357]

 

[CanAm]

Were there any problems reported because of the thinner barrels used on first model? I kind of wish I had waited for this new version with better sights.

AF

Far from problems. Ours were not "thin", just normal compared to other barrels. The barrel must be much thicker to accommodate chokes. It also adds a lot of weight for bush carry. A trade off.

 

[DOOK]

The only problem I had was with concentricity. ...But I am a picky bugger.

 

[CanAm]

The only problem I had was with concentricity. ...But I am a picky bugger.

That seemed to be more of an overzealous polishing, rather than actually thinner on one side. It is common on several shotgun makes I have seen.

 

[DOOK]

I mic'd them both Chris. Both thin on one side. Although the second one had a better squared end.

 

[PowerStroke]

When Dammit When?

 

[Mikjk]

does anyone know what the measurement is for the threading for the bead sight is? 6-48 or 5-40? thanks in advance!

 

[darkshadow]

Do you know when we might know if we are going to get the folders here?


Is your flyer not out yet? seen the one on the site advertising the mag feds already.....

 

[canadianshooter]

Tired 6-48

I tried a 6-48 and pretty sure it wasn't it. Sent it off to have it tapped for 6-48.

 

[Mikjk]

I tried a 6-48 and pretty sure it wasn't it. Sent it off to have it tapped for 6-48.

Thank you!

 

[Splatter]

My bet would be that it is a metric thread.

 

[Wildfoot]

well i was going to buy one of the first grizz's, but decided to wait for the threaded ones.. im soooooo excited for this shotgun. CanAm, how long until you will take my money for one of those new 12" that are comming in.

Will the ghostring sights be the same as in the pics? Are the holes in the reciever universal with other ghost ring setups? Is it drilled and tapped for a scope mount?

 

[CanAm]

You can order when you see the new guns up on the site. The scope holes are the same as Marlin uses, see pics above.

 

[PowerStroke]

8.5" mag fed ???

sweet 666 post count

 

[6gm6]

Any barrels coming in for those of us with the old grizzly?