New Trudeau Blair rules on shotguns

Tokay444 said:
Where’s that guntech loser now?
Click to expand...

He cannot grab a breath to talk like I am from laughing so much. Here I posted this else ware. Try to grasp it

11 pages and no one noticed he didnot install the proper 12ga ring and zero the gauge..Unbelievable how bad you guys what this to be real. No god dam wonder he got over .80
Who is the guy on the end of the dial. This is priceless. Notice he has nothing over the steel balls on the gauge head showing it was zero'd LOL
OMG. However look where he went to measure the bore not on the end of the barrel which was right too bad someone didnot show him how to use the gauge correctly. Show me the ring??? that he has to install in the pic to zero and all of these gauges use them to do it right and it is no where to be seen
This is turning into a gong show for the CSSA
Then he talks about back boring which didnot even start until 1987 like 25 years after that old girl was made

“The heads of our unit are marked with the gauge size, and the rings are marked with the corresponding diameters for easy recognition and use. Example: To measure a 12-gauge barrel, you would install the 12-gauge head on the shaft and slide the .700 ring over the three steel balls on the head. Next, set the dial on the indicator to 0. The 0 represents .700. Inserting the head into the muzzle end of the barrel past the choke area will give a reading larger than 0. For example, 29. This indicates a bore diameter of .729 which is the nominal size for American shotguns and many European shotguns as well. As you pull the head toward the muzzle, the dial will read a lower number and might even go past 0. For example, it might read 95. This would indicate a choke diameter of .695 and thus a Full choke. To determine the actual points of constriction the choke is imparting on the pattern, you would subtract .695 from .729 for a total of .034.


“The heads of our unit are marked with the gauge size, and the rings are marked with the corresponding diameters for easy recognition and use. Example: To measure a 12-gauge barrel, you would install the 12-gauge head on the shaft and slide the .700 ring over the three steel balls on the head. Next, set the dial on the indicator to 0. The 0 represents .700. Inserting the head into the muzzle end of the barrel past the choke area will give a reading larger than 0. For example, 29. This indicates a bore diameter of .729 which is the nominal size for American shotguns and many European shotguns as well. As you pull the head toward the muzzle, the dial will read a lower number and might even go past 0. For example, it might read 95. This would indicate a choke diameter of .695 and thus a Full choke. To determine the actual points of constriction the choke is imparting on the pattern, you would subtract .695 from .729 for a total of .034.
 
Last edited:
3macs1 said:
He cannot grab a breath to talk like I am from laughing so much. Here I posted this else ware. Try to grasp it

11 pages and no one noticed he didnot install the proper 12ga ring and zero the gauge..Unbelievable how bad you guys what this to be real. No god dam wonder he got over .80
Who is the guy on the end of the dial. This is priceless. Notice he has nothing over the steel balls on the gauge head LOL
OMG. However look where he went to measure the bore not on the end of the barrel which was right too bad someone didnot show him how to use the gauge correctly. Show me the ring??? that he has to install in the pic and all of these gauges use them to do it right and it is no where to be seen
This is turning into a gong show for the CSSA
Then he talks about back boring which didnot even start until 1987 like 25 years after that old girl was made

“The heads of our unit are marked with the gauge size, and the rings are marked with the corresponding diameters for easy recognition and use. Example: To measure a 12-gauge barrel, you would install the 12-gauge head on the shaft and slide the .700 ring over the three steel balls on the head. Next, set the dial on the indicator to 0. The 0 represents .700. Inserting the head into the muzzle end of the barrel past the choke area will give a reading larger than 0. For example, 29. This indicates a bore diameter of .729 which is the nominal size for American shotguns and many European shotguns as well. As you pull the head toward the muzzle, the dial will read a lower number and might even go past 0. For example, it might read 95. This would indicate a choke diameter of .695 and thus a Full choke. To determine the actual points of constriction the choke is imparting on the pattern, you would subtract .695 from .729 for a total of .034.
Click to expand...

There seem's to be the Fudd word is getting throw around like crazy lately. Perhaps us more moderate members need to coin a term for enraged folks who are pulling crap like posting "Good, now it's you Fudds turn. How do you like it?"
Maybe Tactical Fudd?
Because all the Tactical Fudds do is bring more division to the sport...easier to pick us off if we are divided.
 
Yep thats it, keep making comments about eachother. Keep fighting, that dose alot of good doesn't it? We now have proof we are ALL in this together and y'all still acting like a bunch of bratty kids. It doesn't matter what guns you own they want them all. Stop being so petty and get over the bull. Both sides have said stupid things. Now get over it.
 
3macs1 said:
He cannot grab a breath to talk like I am from laughing so much. Here I posted this else ware. Try to grasp it

11 pages and no one noticed he didnot install the proper 12ga ring and zero the gauge..Unbelievable how bad you guys what this to be real. No god dam wonder he got over .80
Who is the guy on the end of the dial. This is priceless. Notice he has nothing over the steel balls on the gauge head showing it was zero'd LOL
OMG. However look where he went to measure the bore not on the end of the barrel which was right too bad someone didnot show him how to use the gauge correctly. Show me the ring??? that he has to install in the pic to zero and all of these gauges use them to do it right and it is no where to be seen
This is turning into a gong show for the CSSA
Then he talks about back boring which didnot even start until 1987 like 25 years after that old girl was made

“The heads of our unit are marked with the gauge size, and the rings are marked with the corresponding diameters for easy recognition and use. Example: To measure a 12-gauge barrel, you would install the 12-gauge head on the shaft and slide the .700 ring over the three steel balls on the head. Next, set the dial on the indicator to 0. The 0 represents .700. Inserting the head into the muzzle end of the barrel past the choke area will give a reading larger than 0. For example, 29. This indicates a bore diameter of .729 which is the nominal size for American shotguns and many European shotguns as well. As you pull the head toward the muzzle, the dial will read a lower number and might even go past 0. For example, it might read 95. This would indicate a choke diameter of .695 and thus a Full choke. To determine the actual points of constriction the choke is imparting on the pattern, you would subtract .695 from .729 for a total of .034.


“The heads of our unit are marked with the gauge size, and the rings are marked with the corresponding diameters for easy recognition and use. Example: To measure a 12-gauge barrel, you would install the 12-gauge head on the shaft and slide the .700 ring over the three steel balls on the head. Next, set the dial on the indicator to 0. The 0 represents .700. Inserting the head into the muzzle end of the barrel past the choke area will give a reading larger than 0. For example, 29. This indicates a bore diameter of .729 which is the nominal size for American shotguns and many European shotguns as well. As you pull the head toward the muzzle, the dial will read a lower number and might even go past 0. For example, it might read 95. This would indicate a choke diameter of .695 and thus a Full choke. To determine the actual points of constriction the choke is imparting on the pattern, you would subtract .695 from .729 for a total of .034.
Click to expand...

“RCMP Confirms”
 
funny was contacted by a friend yesterday saying "well Bliar" cleared 12 gauge.... I responded "you ok with a tweet to confirm?" Today he is "well what the fauck this isn't right eh?!".
 
Butcherbill said:
Just wait till the next step is announced, handgun bans by municipalities and central storage to remove the remaining hunting rifles and shotguns from the home. Women’s advocate groups are saying hunting guns are used in domestic violence and homicides, we're all wife beaters and murders in wait right? If it saves one life it’s worth the inconvenience of having to pay for the central storage of your bolt gun if it means you can still hunt with and “own” it.
Click to expand...

This sounds eerily similar to a senators bill a few years ago Bill S-223 iirc


Oh and if they're all about saving 1 life. They should make abortion illegal, that would save atleast one life.....a hour. As the saying goes, these feminazis can't have thier cake and eat it too.
 
fySoYLS.jpg
 
You must log in or register to reply here.
Back
Top Bottom