Norinco CQA - Hot barrel ... break in period?

For a 1.5 moa carbine that shoots at 500m at the most, even there is a 5% gain in performance it is not worth the time to sit there and waste hours of time to clean and scrub. I buy guns to shoot, not to clean. That is why I don't get into bench press shooting !! Lol

Bench press shooting is a whole different game. I don't think their routine is applicable to people who shoot 3 gun or SVC.

To the OP, just shoot and forget about breaking in.
 
For arguments sake it`s a 2% improvement and your rifle is dialed in and it gets a .500 inch group at 100 yds if all things being equal you move back to 1000 yds so what is your group size going to be 5 inches and take 2% off that its 4 inches that is an improvement . You are not going to see a a dramatic improvement in any thing under 500 yds after that it will make a difference .

A 2% improvement on a 5" grouping results in a 4.9" group. Kind of like a 2% improvement on a .5" will result in a .49" group.
 
For a precision rifles I break in my barrels due to the sharp edges/burrs left behind in the machining process. I'd rather not have this material being ground into the barrel. If its a lapped barrel which is the process of removing these sharp edges, burrs and other imperfections then there is no need to break in the barrel. This is just my preference and for a reach out and touch something rifle for the extra time it takes I'll do it. My other rifles I just shoot and clean after I'm done.
 
x2 It's a fighting rifle.

For a 1.5 moa carbine that shoots at 500m at the most, even there is a 5% gain in performance it is not worth the time to sit there and waste hours of time to clean and scrub. I buy guns to shoot, not to clean. That is why I don't get into bench press shooting !! Lol

Bench press shooting is a whole different game. I don't think their routine is applicable to people who shoot 3 gun or SVC.

To the OP, just shoot and forget about breaking in.
 
2003, 2004 trophies on the shelf behind me, I think 2002 and 2007, in a box somewhere. Match director will attest as he would give me a hard time when registering (all tongue and cheek of course).
Lots of shooting sports out there, just got to go out and try.

Rich

Hmm... You sure these are the only years you competed??

TDC
 
For a precision rifles I break in my barrels due to the sharp edges/burrs left behind in the machining process. I'd rather not have this material being ground into the barrel. If its a lapped barrel which is the process of removing these sharp edges, burrs and other imperfections then there is no need to break in the barrel. This is just my preference and for a reach out and touch something rifle for the extra time it takes I'll do it. My other rifles I just shoot and clean after I'm done.

Are you saying you buy barrels for a precision rifle that are not finished/lapped properly??

TDC
 
Are you saying you buy barrels for a precision rifle that are not finished/lapped properly??

TDC

Actually quite possibly I have, since I could not find any information about wether my Rock River Arms varmint barrel was or wasn't lapped during manufacturing I decided I'd rather be cautious than be a fool and not break the barrel in. I'd rather not take chances with $500+ barrels.
 
Actually quite possibly I have, since I could not find any information about wether my Rock River Arms varmint barrel was or wasn't lapped during manufacturing I decided I'd rather be cautious than be a fool and not break the barrel in. I'd rather not take chances with $500+ barrels.

No offense, but an AR is far from a precision rig and RRA is far from high end. What sort of groups are you getting out of it?

TDC
 
Possibly least educated, and anecdote based opinion: More to address the OP, I was a militia bum for a few years, and we never followed a break in procedure. As a matter of fact, my newly issued rifle when I got to garrison was not only new to me, but actually new. Which was a welcome change from the rifle I was issued during basic, in wainwright AB. No telling how many thousand rounds went through that.

Well, it's first range trip was to shilo, to rid ourselves of our remaining training allowance of ammunition. Any one who has gone on one of those wasteful and wonderful trips to the range knows what a torture test that can be for firearms. Occasionally we even split machine gun barrels, not to mention melted plastic from setting them down on sandbags. I started actually trying to get perfect hits on my targets, until a master bombardier told me we'd be there all night if I shot like that. "Go crazy, flip the switch to fun". Mag after mag in full auto. So as you could see in the darkness, little rays of orange light beneath the hand guards. That rifle was so full of carbon, it looked like it was furry.

And that same rifle got me my marksmanship badge the next two years in a row. And while that was the worst abuse I subjected that rifle to, it was not the only one. I'm sure at 500m it's performance may have been affected, but for most, that's the domain of bolt rifles anyway. Like I said, just one mo-bums experience.
 
Back
Top Bottom