Norinco HP9 Accessories

B

Bonus

New member
EE Expired
Rating - 100%
1   0   0
Location
S Ontario
Hi Guys, I just bought a Norc HP9 and I'm looking for some help in tracking down a few accessories for it, all help appreciated.

It's the 14" barrel model and I'd like the +1 with sling point, mag extension
I'd also like to fit the shurshot stock from Remington.
Considering the Burris Speed bead or optic rail that fits the take down pins
Ghost ring sights also considered if they can be fitted

I've polished the bolt and rails and it's going pretty slick now

Open to suggestions for a tactical railed forend, as I'd also like to fit a magpul AFG

Any help or suggestions on the suitability of accessories is much appreciated

Also like to hear about any trigger or additional action works that I could do

Thanks
 
well as we are the go to people for those type of shotgun products, ill wade in on what I think you need.

100% you need to change the mag follower, the one that works the best Is the nork, as the mag tube is metric and a few thou smaller then the Remington is our Mossberg follower
http://sjhardware.com/store/modules.php?name=catalog&file=product_info&cPath=107_123&products_id=682

Over sized safety button is another very good idea, after all this is Canada and shooting with gloves on does happen, no way you will be able to use your safety safely with gloves on, to easy to hit the safety and trigger at the same time when loaded.
http://sjhardware.com/store/modules.php?name=catalog&file=index&cPath=107_177

+1 mag tubes, yes forsure, you have the room so what not use it, only issue is that you need to push out or drill out the indents that hold on the plating end cap retainer.
the issue with doing that is that you will then not have a retaining system to hold the end cap or +1 on.
older shotguns have a ball bearing dedent on the barrel lug.
We have found that it is ideal is this is installed, but if you put the +1 one and tighten is down real hard, nothing comes loose, even after a day of shooting.
Some mag disagree.
http://sjhardware.com/store/modules.php?name=catalog&file=product_info&cPath=107_120&products_id=771

Butt stock is easy to change
forend is undersized so you will need to ream out the hole in the center a bit to be able to fit the forend.
The magpul is nice but its sized inbetween the police length and the sporting length so you will not be able to get a 6 shot side saddle on the side
we also make 2.4.6.7 shot Velcro on detachable side saddles
http://sjhardware.com/store/modules.php?name=catalog&file=index&cPath=107_125

bbb
 
+1 for S&J, I have the follower and the oversized safety for my HP-9.
Just watch if you put a side saddle shell holder, I had to cut a half inch off the fore stock to allow for it.
 
You could consider a hiviz clip on site -- I just put one on and it looks good, but I haven't had it to the range yet
 
I installed Wilson sights, +1 mag extension, magazine follower and mag spring, a Surefire forend and a Spec-Ops recoil reducing stock.

I have a Wilson oversized safety but it won't work with the Spec-Ops stock.

It is a very RELIABLE rig and is my house gun. Beware that it is a heavy shotgun so I have not gone with shell holders.

DSCN1496_zps8e4a6ea0.jpg
 
Deal with confidence with badboybeeson. His products are outstanding and his customer service is better still. I have an AR barrel from him and a bunch of stuff on my 870 "social work" shotgun. all of it is great stuff.
 
You must log in or register to reply here.
Back
Top Bottom