Powder Containers

Smokezm

New member
EE Expired
Rating - 0%
0   0   0
Hey Guys,
I recently read on here that it is best to mix all your powder from 1lb containers into a larger container to ensure burn rate consistency ( This forum is great for learning tips for a newer reloader like me!). I have a few 1lb containers and I was wondering what type of containers do you use to mix/store your powder in? I assume it would have to be airtight, especially since I'm not a real high volume shooter.

Thanks, Matt
 
You can always mix it out in a large bowl or something, then return it to the original containers. Mark them with a "batch' number of your own.
 
I use the 4 Liter laundry soap jugs. I wash them out until there are no longer bubbles in the water then put them in the microwave to warm them up a bit and set them outside, spout down, preferably in sunlight until they are dry inside. Many of these containers come with a shaped pour spout that is removable and are very handy for pouring powder into a measure.

If those jugs stand up to laundry soap they will stand up to powder easily. After all, they are the same type of plastic. Bleach jugs work as well but don't have the handy pour spouts. Cheap and easy.

Just make sure you mark the jugs properly with large tags describing what is in the container.

A four liter jug will hold close to ten pounds of powder when it is full.
 
It's not how strong or thick the plastic is , it is if the plastic that the jug is made out of will get degraded by the powder. Powder will accually eat right through certain types of plastic. The plastic should also not allow light to pernitrate ( that is why powder containers are black) as light will degrade the powder. This is all taken from what I have read on powder storage.
 
Hmm didnt know powder could eat through some plastics like that.

I mixed up around 15#'s of varget awhile back from three different lots. Just used one of the wifes big soup pots.
 
It's not how strong or thick the plastic is , it is if the plastic that the jug is made out of will get degraded by the powder. Powder will accually eat right through certain types of plastic. The plastic should also not allow light to pernitrate ( that is why powder containers are black) as light will degrade the powder. This is all taken from what I have read on powder storage.

That's why I was wondering if any watertight container would do. I wouldn't wan't to degrade my powder in any way (stuff is like gold nowadays. lol). I'd like to find some empty 8lb jugs but we don't see many 8lb'ers down this way. I think I'll use the idea to blend them and then pour them back into their original containers (thanks Dmay), also I may try the laundry soap container idea also ( thanks Bearhunter) , that's what makes this forum great!
 
For the time it takes to mix the powder anything will work. But you likely don't want to store it longer term due to the possible issues.

The black plastic bottles we have now are also black because it's the same static reduction plastic that is used for static sensitive electronics component packaging. Ever notice how the powder clings to the cap seal paper/plastic seal but not to the sides of the bottle itself?
 
+1. That's why the mfr states to not leave powder in the dispenser tube. Don't ask me why I know but Hornady was kind enough to send me a new one for free after the bottom of the original tube shrivel to the point it popped out.
It's not how strong or thick the plastic is , it is if the plastic that the jug is made out of will get degraded by the powder. Powder will accually eat right through certain types of plastic. The plastic should also not allow light to pernitrate ( that is why powder containers are black) as light will degrade the powder. This is all taken from what I have read on powder storage.
 
I recall receiving powder from Higginson in a plastic bag inside of a cardboard box. It must be storable that way or there would be instructions to the contrary. Therefore the opinions expressed about the laundry detergent containers are unfounded.
Enjoy
 
I use a 2-1/2 gallon plastic bucket, that you can buy for about $6 at Home Hardware.
It even comes with a lid. Use a wooden spoon, give it a few stirs, then snap on the lid give it a couple rolls and shakes, funnel it back into your 1lb containers.
 
I disagree :)

Yeah, I wrote something to the effect about people in the USA storing powder in pop bottles - which is why people are so freaked out about storing powder in any other container. Horror stories of powder all over the floor and such. Madness.
As stated, Higginson ships in plastic bags. An while I wouldn't want to store it long term this way, you can mix in another clean container and return back to original bottles.
 
I have a couple of RED TIDE laundry soap containers that have been used to store powder in for over 20 years.

I had several pounds of 4831 I had purchased surplus in large 50 pound paper drums and 25 pound paper drums. Yes, they were all purchased legally from a surplus dealer in Idaho back in the early seventies. This stuff never had any other markings on it other than the jobber that manufactured it and four inch tall, black "4831" numerals along with a manufacture date which indicated it was made in 1942.

I am using up the last of it now but there is still enough for about five more years. This stuff is slower than the newly manufactured Hodgdon's H4831 and quite a bit slower than IMR4831. Hodgdon and others used to sell the surplus 4831 under their own brand names up to the mid seventies. Of course it was a very popular powder as it was so forgiving and was actually quite stable in different temperatures. I remember paying $20 for the 50 pound kegs and $10 for the 25 pound kegs. There were also larger containers but they wouldn't fit in the back of my car.

To show how well this stuff stores, Hodgdon's used to store it outside under big hayshed style roofs with open sides. The powder was all in large wooden crates that were made out of some sort of treated hardwood with heavy treated paper on the interior. These large crates were approximately four feet square. If memory serves the ones I remember were packed with large paper drums of different sizes, likely for easy loading into feed hoppers at loading facilities.

At any rate, the powder I am still using is over seventy years old and because it has been stored properly and because of the way it was manufactured it is still just as consistently reliable as it was when I purchased it in the late sixties.
 
Back
Top Bottom