Precision/Sniper/Tactical
- Thread starter Farmboy
- Start date
Ivan Smythe
CGN Regular
- Location
- Northern BC
some of the rigs i use for long range shooting
wolf taken at 480 yds with this custom .300 WSM
personal best on a coyote at 683 yds with custom.300 WinMag
wolf taken at 480 yds with this custom .300 WSM
personal best on a coyote at 683 yds with custom.300 WinMag
Last edited:
punkrockboy
CGN Ultra frequent flyer
- Location
- Eastern Bantario!
Nice guns, Nice DEAD coyotes!!!
Ivan Smythe
CGN Regular
- Location
- Northern BC
Brainless,
both.
in-laws have a cattle operation in northern BC.
so when i'm not calling them in there is usually a dead calf or two, or even the gut pile from a slaughter cow to use as bait.
in the third picture you can see two of the calls i use hangin' around my neck.
both are long distance distress calls, jackrabbit and bleating fawn.
for closer in i use a mouse squeeker.
if it's the right time of year i'll also use gathering crows.
i.
both.
in-laws have a cattle operation in northern BC.
so when i'm not calling them in there is usually a dead calf or two, or even the gut pile from a slaughter cow to use as bait.
in the third picture you can see two of the calls i use hangin' around my neck.
both are long distance distress calls, jackrabbit and bleating fawn.
for closer in i use a mouse squeeker.
if it's the right time of year i'll also use gathering crows.
i.
Last edited:
Ivan Smythe
CGN Regular
- Location
- Northern BC
another one of my faves.
Ivan Smythe
CGN Regular
- Location
- Northern BC
Coyote hides?
as of late not a whole lot of interest in them commercially.
i used to however get $25-$30 for the whole coyote, people would use the fur on muk-luks and such.
mostly these days they just get their picture taken with me and my rifle and then become a small part in the big circle of life(they feed the worms).
as per,
i.
as of late not a whole lot of interest in them commercially.
i used to however get $25-$30 for the whole coyote, people would use the fur on muk-luks and such.
mostly these days they just get their picture taken with me and my rifle and then become a small part in the big circle of life(they feed the worms).
as per,
i.
OH, that too bad, you could probally make a nice gun case out of them instead of going to waste!
Just a curious question here, who build you rifles for you, the reason I ask , because I am looking for a good gunsmith, I got 2 long rem700 action and wanted to build one in 300WM and the other 338Rum, adn would you recommended this gunsmith?
here are my Precision!
here are my Other Precision!
Just a curious question here, who build you rifles for you, the reason I ask , because I am looking for a good gunsmith, I got 2 long rem700 action and wanted to build one in 300WM and the other 338Rum, adn would you recommended this gunsmith?
here are my Precision!
here are my Other Precision!
Last edited:
haha
Ivan Smythe
CGN Regular
- Location
- Northern BC
Gunsmith?
Just a curious question here, who build you rifles for you, the reason I ask , because I am looking for a good gunsmith, I got 2 long rem700 action and wanted to build one in 300WM and the other 338Rum, adn would you recommended this gunsmith?
Gunboy,
i get all the work done on my rifles these days by Rod and Greg at Corlane's in Dawson Creek, BC. i recommend them highly. in fact i was just there this morning to pick up a couple of rifles i had badger bolt knobs installed on. another beautiful, timely and cost effective operation courtesy of the folks at Corlanes.
i.
Just a curious question here, who build you rifles for you, the reason I ask , because I am looking for a good gunsmith, I got 2 long rem700 action and wanted to build one in 300WM and the other 338Rum, adn would you recommended this gunsmith?
Gunboy,
i get all the work done on my rifles these days by Rod and Greg at Corlane's in Dawson Creek, BC. i recommend them highly. in fact i was just there this morning to pick up a couple of rifles i had badger bolt knobs installed on. another beautiful, timely and cost effective operation courtesy of the folks at Corlanes.
i.
pebsykid
I think you should try and become a better shooter, so just keep one of those and sell/loan the rest to me, Ill take good care of them!!
LET me know which one you like, and I will handed to you!
Ivan Smythe
I am thinking about getting a manual lathe this summer for my Garage, but I am too busy at the moment to play all out at the moment, Let me know if I can be of some help.
I think you should try and become a better shooter, so just keep one of those and sell/loan the rest to me, Ill take good care of them!!
LET me know which one you like, and I will handed to you!
Ivan Smythe
I am thinking about getting a manual lathe this summer for my Garage, but I am too busy at the moment to play all out at the moment, Let me know if I can be of some help.
Last edited:
