Raised cheek add ons

[mike Crawford]

Does any one make a raised cheek piece that slips or laces on too the stock like you see the shell holders .
I find that with some guns you tend to lift your face away from the stock to get a full view into the scope .
On some target rifles they have an adjustable cheek piece for that .. It would be a handy rig to have

 

[Albertarookie]

I have seen a few different neoprene cheek risers online but when I look in stores I can never seem to find any. I would like to pick a couple up

 

[mike Crawford]

I seen a guy with a fiber glass stock use a piece of 2x2 wood that he shaped to fit the stock .. he had it attached by two screws .. and when removed yuo could see two small holes in the stock but only if you knew what too look for.. when it was attached it looked a bit odd .. But when I shouldered the gun the scope was right there .. some guns stocks were built for open sites; and when a scope is attached ; you have to lift your face off the stock to see though the scope .. One of the reason I dislike the see though mounts on Remington 7400 and 7600 rifles

 

[stubblejumper]

There is also a Beartooth comb raising kit, that isn't permanent. I avoid the issue, by avoiding the large diameter scopes, and mounting my scopes as low as practical.

 

[Diablo7101]

I have one made by Triad Tactical ....it's a strap on with zipper pouch and shell holders. Very comfortable suade type cheek pad and lots of different styles and options to choose from.

 

[josquin]

There is a company in Oregon, www.cheeknstock.com/main.html, that makes a nice-looking one. I'm thinking of ordering one for my Brno Fox .222.

Stuart

 

[lowe160]

Ebay is your friend for cheek risers! I even picked up a left handed one for the wife. They were about $30-40.00.

 

[mike Crawford]

Thanks too both of you for posting .. I am going to try one from each company .. I can see where each on has some features I like for sure

 

[mike Crawford]

Both companies save too book marks

 

[stubblejumper]

Meadowindustries also makes a few products to raise the comb.

 

[regulate34]

for the girlfriends 243 I ended up getting a slip over shell holder and added foam under it to get the exact height she needed.

ill go get some pics

 

[regulate34]

cheep and functional. I know it is a little rough but works for her

 

[mike Crawford]

As long as it works I would not hesitate to use that setup .. I bothers me to have to lift my face to get a good view in the scope ,

 

[Salty]

was going to get this after getting a 20 moa base on my 223 but ended up getting used to it without a riser. 1/4 to 3/4 lift on these all leather says cabellas. 30 bucks

 

[mike Crawford]

What did you use for a search to find these at cabella's anything I type in to do with riser gets bow risers

 

[stubblejumper]

How about this?

accu-riser.com/products/Accu%252dRiser-Monte-Carlo-Strap-On-Comb-Raiser.html

 

[Salty]

its under recoil accessories mike.. Canadian site

 

[hawk-i]

for the girlfriends 243 I ended up getting a slip over shell holder and added foam under it to get the exact height she needed.

ill go get some pics

Is she left handed?

 

[theiss]

Google cheek pad or cheek rest. Some will show bike helmet pad, but some will be for shooting. Mmake sure theyre two separate words.

 

[TheTooner]

There is also a Beartooth comb raising kit, that isn't permanent. I avoid the issue, by avoiding the large diameter scopes, and mounting my scopes as low as practical.

A Beartooth kit and an extra Beartooth sleeve with shotshell loops solved two guns for me. I also have a well-made leather lace-on by the holster maker TripleK but it's for a gun that hasn't been built yet so I can't completely vouch for it.