Rifles let's see them??

Camp Cook said:
My_Stainless_Steel_Black_Gray_Laminate_Stocked_Firearms_002.jpg
Click to expand...

Holy salt and pepper fetish!!! They all look super clean though. Nice collection.
 
My only suggestion would be to go to a Warne or Leupold 2 piece Weaver style base then mount an XS Sights Tall Weaver Backup Ghost Ring rear sight then I would figure out how tall the front sight would need to be.

Is you front sight post dove tailed that you could take off and replace with a taller XS front sight post?
 
SuperCub said:
I was going to use one of those reciever sights that attaches to the weaver base, but the comb is too high.

I'm going to look into a complete nuther set of higher sights [front and rear] from NECG. I need something high enough to use with a straight comb stock. Any suggestions?


.
Click to expand...

Google Brockman's custom gunsmithing, he makes a pop up peep sight that is integral with a warne base and used with warne quick release mounts. He only advertises M70 and Dakota I think, but he makes one for the M700. It requires drilling and tapping one hole in the receiver. It is a slick looking unit.
 
stuckon308 said:
Holy salt and pepper fetish!!! They all look super clean though. Nice collection.
Click to expand...

Not really check out the dirt on the shoulder strap on the second rifle down from the top.

I use my guns hard they are tools not safe queens well except for the bottom right one it is a Browning BL22 22LR I haven't had a chance to really break it in yet...
 
Camp Cook said:
My only suggestion would be to go to a Warne or Leupold 2 piece Weaver style base then mount an XS Sights Tall Weaver Backup Ghost Ring rear sight then I would figure out how tall the front sight would need to be.

Is you front sight post dove tailed that you could take off and replace with a taller XS front sight post?
Click to expand...
The bases are all-steel Weaver style. I like them. I will look into your suggestion as I prefer peep sights over bbl sights.

The front sight is a std Remington factory sight.

.
 
Here is a few of mine, sorry for the quality but I spent the camera money on the new russian SKS.
PICT0208.jpg

Top to Bottom are:
MAnlichter Carcano 6.5
Enfield Parker Hale 303
Stevens bolt action 12 guage shotty
Stoeger 12 guage pump with recoil compensator
Mauser M98 with ATI stock 308
PICT0204.jpg

SAvage accutrigger bvtss .17 HMR
Black Powder thompson Hawken 50 cal
RUger Hawkeye with lc6 trigger and laminate stock in 25.06
Smith and WEsson 357 magnum
PICT0203.jpg
 
Camp Cook said:
Not really check out the dirt on the shoulder strap on the second rifle down from the top.

I use my guns hard they are tools not safe queens well except for the bottom right one it is a Browning BL22 22LR I haven't had a chance to really break it in yet...
Click to expand...

Oooooh yeah. I see that now. What a piece of crap. I'll trade you for my Cooey to make you feel better.
 
SuperCub said:
I was going to use one of those reciever sights that attaches to the weaver base, but the comb is too high.

I'm going to look into a complete nuther set of higher sights [front and rear] from NECG. I need something high enough to use with a straight comb stock. Any suggestions?


.
Click to expand...

I have a mark X Mauser with a Butler Creek stock on it. The Iron sights that where used where take offs from a Remington 700 fitted with a true glow front sight, and the rear ground to express contours.
Still slightly low for the stock, but probably as good as you're going to get.
Mike
 
You must log in or register to reply here.
Back
Top Bottom