Story of a Winchester Mod.100

LawrenceN

CGN Ultra frequent flyer
Rating - 100%
240   0   0
I really like the Mod.100 Winchester semi-auto's. Personally, I think they're one of the most elegant of the semi's, followed by the Remington, and then the BAR. Though I'm predominately a bolt guy, I like the idea of having the quick follow-up shot for certain occasions so I started looking for a nice semi. I've had several of these Mod.100's pass through my hands and sold them off for one reason or another. I lucked upon my "keeper". I found one that basically had 1 box of ammo through it back in '64, was cleaned and put away and sat in a closet for the next 50 + years. Essentially a new rifle and not even really broken in. It came with the nice oak motif basket weave stock but I personally like the older beefier stock from the earlier models. Granted, they're not as pretty but they are a better fit for my hands and less prone to cracking and damage. I tore the rifle down and indeed, it was almost pristine! I sold the nicer stock at a gun show after I got my older used one. These rifles are finicky in what they like in ammo, but I found an acceptable 150 gr. deer load (1-1/2"-2" @ 100 yds.). The dings and dents in the stock always kind of bugged me, as did the fact that the plastic butt would beat up my old bones, so I decided to cut the butt down, install a recoil pad, and refinish the stock. So my fellow gunnies, here's the result. Comments and/or observations more than welcome.
 
Last edited:
Nice job on that 100 .I also have a pre64 308 rifle and a 308 carbine . Owned them for years they function well with win 180 silvertips .
 
Last edited:
Nice work, looks good with the oil finish on that wood. Looks like you fit that recoil pad well too, typically not something I care for but had to do the same recently on a rem 600 to get the lop I needed. I've gotta get out with my post 64 win 100 it's not had any love for a bit. Are you reloading for it or running factory ammo? Ive had cycling issues with my mild hand loads behind 165gr pills, need to check but believe i was using H4895. Thanks for sharring.
 
It looks really nice, they were always one of my favorite rifles. One of the best looking rifles out there. I carried one hunting for many years, as well as most of the fellas in our camp. A few years ago mine developed a problem were it wouldn't eject the spent brass, and sometimes failed to feed the next round properly. It would get jammed trying to go in the chamber. Ive had it apart many times, twice into the shop,and its spotlessly clean. I'm still trying to get it working well.
 
Nice work, looks good with the oil finish on that wood. Looks like you fit that recoil pad well too, typically not something I care for but had to do the same recently on a rem 600 to get the lop I needed. I've gotta get out with my post 64 win 100 it's not had any love for a bit. Are you reloading for it or running factory ammo? Ive had cycling issues with my mild hand loads behind 165gr pills, need to check but believe i was using H4895. Thanks for sharring.
Like you, I've had to install recoil pads to get the correct LOP on some other firearms. In the case of this rifle, I took about 3/4" off the butt and installed a 1" Limbsaver recoil pad. There was some damage to the wood where it met the butt plate so that's gone and now I have a nice clean line for the whiteline spacer. I'm glad you like the oil finish as much as I do. As to my handloads, I mostly hunt whitetail hereabouts, and I'm loading a 150 gr. Hornady flat base soft points on top of 45 gr. of Accurate 2495.
 
It looks really nice, they were always one of my favorite rifles. One of the best looking rifles out there. I carried one hunting for many years, as well as most of the fellas in our camp. A few years ago mine developed a problem were it wouldn't eject the spent brass, and sometimes failed to feed the next round properly. It would get jammed trying to go in the chamber. Ive had it apart many times, twice into the shop,and its spotlessly clean. I'm still trying to get it working well.
They have a bad rep for being very sensitive regarding ammo. I'm fortunate in that mine has never had any issues with feeding or extraction. I was told they perform better with the heavier bullets but I haven't put that to the test as yet. If I ever get a chance to go moose hunting, or maybe just for fun, I'll run some 180 gr. bullets through it.
 
It looks really nice, they were always one of my favorite rifles. One of the best looking rifles out there. I carried one hunting for many years, as well as most of the fellas in our camp. A few years ago mine developed a problem were it wouldn't eject the spent brass, and sometimes failed to feed the next round properly. It would get jammed trying to go in the chamber. Ive had it apart many times, twice into the shop,and its spotlessly clean. I'm still trying to get it working well.

I walked this walk many years ago.
Discovered a crack in one of the extractors.
'nuff to make it not work.
Take it apart again and use a magnifying glass and have a looky-see at them.
Maybe history will repeat itself.
 
Last edited:
I really like the Mod.100 Winchester semi-auto's. Personally, I think they're one of the most elegant of the semi's, followed by the Remington, and then the BAR. Though I'm predominately a bolt guy, I like the idea of having the quick follow-up shot for certain occasions so I started looking for a nice semi. I've had several of these Mod.100's pass through my hands and sold them off for one reason or another. I lucked upon my "keeper". I found one that basically had 1 box of ammo through it back in '64, was cleaned and put away and sat in a closet for the next 50 + years. Essentially a new rifle and not even really broken in. It came with the nice oak motif basket weave stock but I personally like the older beefier stock from the earlier models. Granted, they're not as pretty but they are a better fit for my hands and less prone to cracking and damage. I tore the rifle down and indeed, it was almost pristine! I sold the nicer stock at a gun show after I got my older used one. These rifles are finicky in what they like in ammo, but I found an acceptable 150 gr. deer load (1-1/2"-2" @ 100 yds.). The dings and dents in the stock always kind of bugged me, as did the fact that the plastic butt would beat up my old bones, so I decided to cut the butt down, install a recoil pad, and refinish the stock. So my fellow gunnies, here's the result. Comments and/or observations more than welcome.
[/QUOT

Looks really sharp man! I've had a love affair with 100s since my first exposure to one.
 
Looks good, might want to redo the checkering on it. Pick up a tool from brownels or midway or something and see if there is enough groove to guide you to recut it maybe.

But.. Bottom line, if your happy with as she be, thats all ya need.
 
Looks good, might want to redo the checkering on it. Pick up a tool from brownels or midway or something and see if there is enough groove to guide you to recut it maybe.

But.. Bottom line, if your happy with as she be, thats all ya need.

I had that in mind and thank you for the contacts. I was looking at picking up a fine"V" point wood carving chisel but I'm wondering if there's any gunsmiths doing stippled stocks. I purchased a budget Mossberg Patriot with the walnut stock and DAMN, is that thing accurate and I love the stippled stock on 'er.
 
My Dad's would shoot nothing other than 150gr bullets and if you didn't let the bolt slam freely it would misfire.Yes it had the replacement firing pin.
 
Nice job on the gun.


I have a carbine that is very nice to carry.

We have two in my camp and last year the other one failed to fire on the only deer we saw, until the last day.

Mine having just gone through the problem, I was able to help. These guns will gum up something awful.

Had to completely disassemble mine and put it through an ultrasonice bath. Now it works perfectly again.
 
I had one I bought at an auction once for $80 got it home and found the one rail of the piston was broken. Gunsmith in Edmonton tig welded it and I traded it off for a another rifle to the same gunsmith. Was in 284. Never found another to buy in 284 so went to a Model 88 instead.
 
Back
Top Bottom