Titegroup with cast in the 30-30
- Thread starter brewmech
- Start date
5 gr will likely be quite light but it should work. Just make sure the bullet is not stuck in the barrel before the next shot 
I haven't tried TG in reduced 30-30 loads yet but have been researching it. Titegroup is getting a reputation for good results with reduced loads. Here is some more info I found. http://castboolits.gunloads.com/showthread.php?115972-Titegroup-for-cast-rifle-loads
I haven't tried TG in reduced 30-30 loads yet but have been researching it. Titegroup is getting a reputation for good results with reduced loads. Here is some more info I found. http://castboolits.gunloads.com/showthread.php?115972-Titegroup-for-cast-rifle-loads
I use 5gr of titegroup in my 303 british with a 100gr bullet. Thats good for 950fps no filler. Just a 22long case full and poured in my 303 case and bullet placed on top. (Actually the 22 lr case is only about 4.2gr so i made a bigger scoup to give an even 5 gr.
ive used down to 2.5 gr and got 700fps and a stuck bullet a few times. Ive never had issue with 5 gr. Ive tried up to 7gr and that worked fine but a little loud for what im using it for.
Hodgdons reloading lists the 308win with 160gr cast bullet and 8gr titegroup (no min or max only 8gr) and thats good for i believe 24,000psi and 1400 fps.
ive used down to 2.5 gr and got 700fps and a stuck bullet a few times. Ive never had issue with 5 gr. Ive tried up to 7gr and that worked fine but a little loud for what im using it for.
Hodgdons reloading lists the 308win with 160gr cast bullet and 8gr titegroup (no min or max only 8gr) and thats good for i believe 24,000psi and 1400 fps.
I've seen 30-30 loads from 4.5 gr to 9 gr on different internet forums. 5 gr should be fine.
These are good places to look for reduced load data.
http://www.hensleygibbs.com/edharris/backcreekdiary.htm
http://www.gmdr.com/lever/lowveldata.htm
These are good places to look for reduced load data.
http://www.hensleygibbs.com/edharris/backcreekdiary.htm
http://www.gmdr.com/lever/lowveldata.htm
Last edited:
I have used TG in 6,5x55, 8mm Mauser, and .308. I have gone as low as 4gr in 8mm, and it pushed the ball out just fine. Found many of the bullets the following spring with only rifling marks for deformity It's too low a load for anything other than seeing if it would work.
Depending on intent (seeing how fast or slow you can push the bullet), and working from your 5gr start make only tiny incremental changes. A little change in pistol powder charge makes a noticeable change over a chrono.
Depending on intent (seeing how fast or slow you can push the bullet), and working from your 5gr start make only tiny incremental changes. A little change in pistol powder charge makes a noticeable change over a chrono.
MasterChaud555
Regular
Beat me to it! I've had very good luck with the information from GMDR.com. Obviously use at your own risk though.
I got titegroup[TG] only for fun plinking rifle rounds. I don't reload pistols at all. All my cast shooting manuals call for different powders than that. As suggested Unique is in any cast recipe I have access to, as is "2400". I can't find 'em! TG is easy to find, not position sensitive (so far....I've fiddled only), and a little goes a long way.
With a lubed, GC bullet, you could also work down your fav 30-30 powder for equivalent weight.
I haven't used TG, but have fired off several pounds of 700X in various light rifle loads. I now use Unique, mostly because I scored a 10 lb. mother lode of it at a gun show, all for the price of about a pound and a bit. One of the nicest loads I've tried lately is 10 to 10.3 gr. Unique under a 155gr. Lee gc ww in .308, fired from an Israeli Mauser 98.
