Value of a Beretta 682 combo

Pocketsx

Member
Rating - 100%
1   0   0
I have a buddy who is looking to sell his Beretta 682 o/u combo and I was wondering if anyone knows what it should be worth. It has quite a few years on it. I'd guess around 20. He's done a lot of mods over the years. Adjustable comb and butt pad. At least I think that what it's called. New ejectors. The o/u barrel is 30' and has briley extended choke tubes. The unsingle barrel is either 32' or 34' also with briley tubes.

Any ideas on a value?
Thanks
 
Pictures would certainly help. Lots of fellows will pay a premium for a nicely figured wood stock and fine checkering.

Where is the position of the lever in relation to the centreline of the gun? To the right is good, to the left, not so much. To the left shows that the gun has fired lots of shells over the course of its life.

There were a few different models of 682's made as well. I have an "S682X". There is an "S682" and also a plain "682". Newer models are 682 gold e's.

New 682 gold e combos can be had for 4500.00 off the shelf.

If you get talking to your friend, ask him some details and post them here. I am sure there will be others along to share their opinion.
 
One of the considerations might be to what extent do the modifications he's done mean to you........ie. will you have to change much to make the gun fit you etc. ..............My opinion of price would be close to one of the other posters.....probably $2200-2500.....depending on the wood, any ding,bangs, etc.
 
Where is the position of the lever in relation to the centreline of the gun? To the right is good, to the left, not so much. To the left shows that the gun has fired lots of shells over the course of its life.

I assuming you mean the lever to open the gun correct? If it is trending to the left what does that mean? Needs some work by a gunsmith? Or does it mean that it's not repairable?

I'll look tomorrow. I'm going to meet up with the owner.

Thanks
 
Yes, the lever to open the gun .

From the factory, the lever (when gun is closed) points to about the 5:00 position. After thousands and thousands of rounds, (on a Beretta, it may happen sooner on less quality brands) the lever moves to the left as the shoulders wear from opening and closing. It really isn't too much of a concern in terms of function, it is just something that a potential buyer can look at to determine how much use the gun has had. For what it is worth, my 682's lever is just a hair left of the 6:00 position, and I am the second owner. I estimate that I have shot about 25,000 rounds through it, and the lever was just right of centre when I bought it.

Hope this helps,

James


I assuming you mean the lever to open the gun correct? If it is trending to the left what does that mean? Needs some work by a gunsmith? Or does it mean that it's not repairable?

I'll look tomorrow. I'm going to meet up with the owner.

Thanks
 
There are 4 sets of "pins" that lock the barrel closed to the receiver. They aren't pins, but that is the easiest way to describe it. Some people snap them shut and others hold the lever to the right and release the lever after closing the gun. If this is still his first set, the cost of replacement is much lower than if it is the last set. Each set is larger in diameter than the previous set. The holes in the barrel become enlarged. The new set is installed and the barrel holes are drilled to fit the new "pins". After the fourth set you have to weld up the holes in the barrel and then start over. It is not an extremely costly repair until you get to the point of welding up the barrels. Once the lever gets close to 7:00 it will start to pop open when the gun is fired.
 
For what its worth, the gunsmith I talked to said that you should get about 500,000 rounds on the first set of "pins" after which they can be rebuilt for about $200. The rebuilt pins should give you another 500,000 rounds and after these are worn out, it is too costly to try and repair. After a 1,000,000 rounds, treat yourself to a new gun.
 
Back
Top Bottom