WK180-c / WS-MCR what accessories should we make?

[jiffx2781]

RCMP doesn't allow it to be part of the barrel length.

You missed the great big word INTEGRATED

 

[Dexter Morgan]

" RCMP doesn't allow it to be part of the barrel length. "

They do. But only if it's all machined from one solid piece of steel.

 

[Baitcaster]

Bolt handle with a stronger magnet and/or tighter fit so it doesn't chew up the receiver.

 

[Baitcaster]

One modification I would like to see is for the 180c is anti wobble shim as per say to stop the twist between the upper and lower , yes I also know the rubber o ring trick. Addressing on the older 180 k's the twist is terrible, cocking handle and piston rods on top of list too.

This

 

[Arcteryx]

One modification I would like to see is for the 180c is anti wobble shim as per say to stop the twist between the upper and lower , yes I also know the rubber o ring trick. Addressing on the older 180 k's the twist is terrible, cocking handle and piston rods on top of list too.

This one please

 

[adriel]

Stock adapter piece that has a picatinny rail interface so we can use new style folding and lightweight stocks.

 

[Arcteryx]

Is it possible to put in shorter set screws under the gas block so it doesn't interfere with the bottom M-lok?

 

[cdnshooter]

Folding stock adapter to use existing buffer tube

 

[1899]

Have you guys at TNA considered making complete 180 style rifles from scratch?

I'm sure there's a market for something of better quality, even if it's at higher price tag.

This. I want one badly, but I just read way too much stuff that would drive me crazy. Is it really that hard and that much more expensive to build it right in the first place?

 

[Ustauk]

Folding stock adapter to use existing buffer tube

Rather then doing this from scratch, you may want to retail Matador Arms Canadian built folding stock adapter.

 

[Porkchopsandwhich]

I'd like to see a light weight barrel (faxon?) and a light weight handguard (carbon fiber)

 

[offgrid]

thanks

 

[wolf300H&H]

Hey where do I get a bi pod adaptor for that style of hand guards on the WK please anyone know ?

 

[NavyShooter]

How about a nice set of walnut furniture. Handguards, pistol grip and stock.

I'd be down for that.

 

[turnsean]

Perhaps a little ambitious, but I think the production of a Retro Upper would be an extremely popular venture. The success of the Brownells retro line speaks for itself. Ideally this upper would include the original charging handle, a dust cover, integrated irons, and a short section of Picatinny rail for optics. A reproduction retro handguard with the ability to take small sections of Pic rail on the side to facilitate the addition of lights and other force mods would be awesome.

 

[OhMrFister]

retro furniture, gas block front sight, and low pro iron sights

 

[kreativei]

OK, here it is, must haves (please):

1. 18” mlok hand-guard - allows use of blast shields and gives a great look
2. Longer charging handle - who’s hands do these small handle’s fit anyhow

I’d love the above, seriously.

I bet lots would be.

 

[ptodoruk]

WK-180 vise block. I used a router to make one out of UHMW. But an off-the-shelf would be cool.

 

[PSYLNZ]

AK 74 Style wooden butt stock

AK 74 Style wooden pistol grip

And this might be a little over the top, but...
AK 74 Style wooden hand guard, scaled up in length to look better on the 2.4 inch longer barrel of the 180. With picatinny rail where traditional AK style rear sight would be, and a fake gas tube to complete the look. Fake gas tube could hold a cleaning brush, and underside of handguard could hold cleaning rod, like an AK does.

 

[375 RUM]

.350 Legend barrel, Pencil profile 18.6

this^^^^ and 300blkout barrel ; folding stock adapter