BCL15 Upper/Lower Sets $89.95, Non Cerakoted...in the Raw

Chumlee Bumsnag said:
Looks great. Are you happy with the Cerama Coat?
Click to expand...

Yes, however some words of advice... Super light coats; I had a couple of small runs and sags to deal with; so I had two moderate weight coats; try for 3 or 4 lighter coats. Unlike anodized or powder coat, I expect that if the finish get's damaged, you can de-grease, redcoat and bake to touch up. Cheaper than farming it out (1/2 -1/3 the cost), but at $50 bucks for a little can, it is more expensive than it should be.

I would use it again; no question. BTW it is much darker than in the photo; must be the flash that makes it look gold. Gold would not be bad. LOL
 
Putz57 said:
Barrie would have been convenient. Thanks for pointing them out, I'll reach out to them on Monday.



That's the same one I have. Came with two bottles of unmarked media. I'll play around with it, maybe it will do the job as it is. I have my can of Cerama-cote and now itching to get my receivers done.
Click to expand...

The bottle I got from CTC was labeled, if I recall rightly, 200-400 grit. It looked the same as the stuff he got with it. I'm certain that it is repackaged used grit, as there was some crap in the bottom of the bottle. At $13.00, that is way more than it is worth, but go easy, and it is plenty to do your lower.

BTW, I learned that you can regulated the sand by tightening and loosening the cap on the sand tank, allowing more or less air to feed the sand into the venturi. You will need a full face shield; when done, after 3 pints of beer, I was still spitting sand!! Set it at the pressure specified in the directions.
 
Meroh said:
The bottle I got from CTC was labeled, if I recall rightly, 200-400 grit. It looked the same as the stuff he got with it. I'm certain that it is repackaged used grit, as there was some crap in the bottom of the bottle. At $13.00, that is way more than it is worth, but go easy, and it is plenty to do your lower.

BTW, I learned that you can regulated the sand by tightening and loosening the cap on the sand tank, allowing more or less air to feed the sand into the venturi. You will need a full face shield; when done, after 3 pints of beer, I was still spitting sand!! Set it at the pressure specified in the directions.
Click to expand...

Neat trick, I'll try and post my results once I can get some time in the garage. I found a smokin' deal on kijiji for a bench top cabinet so the beer should be safe from any additives.
 
So after seeing another thread about swapping pistol calibers and registration info, I got curious as to these.... The registration lists frame only. All my other registrations have a barrel length specified. After completing this build with a barrel is the CFO supposed to be notified to update these registrations?
 
Bert_PL said:
So after seeing another thread about swapping pistol calibers and registration info, I got curious as to these.... The registration lists frame only. All my other registrations have a barrel length specified. After completing this build with a barrel is the CFO supposed to be notified to update these registrations?
Click to expand...

I’d be interested in this answer as well. Thanks
 
Bert_PL said:
So after seeing another thread about swapping pistol calibers and registration info, I got curious as to these.... The registration lists frame only. All my other registrations have a barrel length specified. After completing this build with a barrel is the CFO supposed to be notified to update these registrations?
Click to expand...

Yes, you have to call in on completion with barrel length and caliber.
 
The Cerama Coat was super easy to apply. I'm really happy with the Olive Drab. It's a little darker than I expected but I'm digging it. Now to gather some parts! 2018-08-14 21.46.16.jpg
20180814_214253.jpg
 

Attachments

  • 2018-08-14 21.46.16.jpg
    2018-08-14 21.46.16.jpg
    33.4 KB · Views: 194
  • 20180814_214253.jpg
    20180814_214253.jpg
    33 KB · Views: 184
Marcie will be contacting the remaining 21 people who ordered these and processing refunds/cancelling the orders. They still aren't transferred into our inventory and from our calls today it doesn't look like it will happen any time soon. Our apologies for the issues but the it's beyond our control at this point.

Ryan
 
Chemist said:
Marcie will be contacting the remaining 21 people who ordered these and processing refunds/cancelling the orders. They still aren't transferred into our inventory and from our calls today it doesn't look like it will happen any time soon. Our apologies for the issues but the it's beyond our control at this point.

Ryan
Click to expand...

Thanks anyways Ryan, appreciate you working to get these transferred.
 
Chemist said:
Marcie will be contacting the remaining 21 people who ordered these and processing refunds/cancelling the orders. They still aren't transferred into our inventory and from our calls today it doesn't look like it will happen any time soon. Our apologies for the issues but the it's beyond our control at this point.

Ryan
Click to expand...

Damn, this really sucks. Is there any way to contact the people who were affected by this when these do get transferred to you guys, so that we can get first crack at ordering these again?
 
Chumlee Bumsnag said:
The Cerama Coat was super easy to apply. I'm really happy with the Olive Drab. It's a little darker than I expected but I'm digging it. Now to gather some parts!View attachment 198445
View attachment 198446
Click to expand...

That looks really good. Definitely darker than the green I was expecting. Have you ever done a handguard? I’m still weighing my options for the entire build but I want the handguard done. Looks difficult tho!
 
You must log in or register to reply here.
Back
Top Bottom