r34skyline
CGN Ultra frequent flyer
Whats that on the muzzle? Is it like a b&t version of the blast warden from surefire?
Heckler & Koch MR223A3 question
- Thread starter Casperpan68
- Start date
Whats that on the muzzle? Is it like a b&t version of the blast warden from surefire?
That is a damn nice setup. How does that compare to a regular Comp/Brake? I assume it diffuses the blast and directs it forward instead of the side and up? Does it still mitigate perceived recoil better than a birdcage?
r34skyline
CGN Ultra frequent flyer
Is it fairly flashy? Or does it do a decent job of flash suppression as well. The 2 chamber comp I mean. The a2 in my experience has done a good job of flash suppression in my experience.
I am not sure if I want to keep the A2 but if I do get something different I like the idea of diverting the blast, My Armalite is ruthless blast wise.
Im looking to get a new mount for my Nightforce NX8, I was going to choose the Spuhr sp3001(30mm - 1.18in) or sp3026(32mm - 1.26in). My Larue SPR 1.5 (1.5in) mount is a bit tall for my liking. From what Spuhr's site said I should take the Diameter of the objective with lens cover and divide by two to get a Minimum Theoretical Height (45.3/2=22.65mm) So I should be able to go as low as 23mm and still clear the rail, correct?
What Height have you guys gone with for your LPVO's? Also the Drum/Diopter on rear sits 29.6mm by my rough measurement. I get a really nice cheek weld at that height so I was hoping I could get a mount to sit that height. Spuhr mounts are not cheap and I do not want to screw up and get the wrong height. Kind of sucks but the Drum is in the way and I have to remove it to drop on the NX8 or Elcan cause they look cool on the rifle.
Im looking to get a new mount for my Nightforce NX8, I was going to choose the Spuhr sp3001(30mm - 1.18in) or sp3026(32mm - 1.26in). My Larue SPR 1.5 (1.5in) mount is a bit tall for my liking. From what Spuhr's site said I should take the Diameter of the objective with lens cover and divide by two to get a Minimum Theoretical Height (45.3/2=22.65mm) So I should be able to go as low as 23mm and still clear the rail, correct?
What Height have you guys gone with for your LPVO's? Also the Drum/Diopter on rear sits 29.6mm by my rough measurement. I get a really nice cheek weld at that height so I was hoping I could get a mount to sit that height. Spuhr mounts are not cheap and I do not want to screw up and get the wrong height. Kind of sucks but the Drum is in the way and I have to remove it to drop on the NX8 or Elcan cause they look cool on the rifle.
If you dont mind me asking, where did you source your Comp and the B&T Diffuser? Cant seem to find them.
Damn that looks great. Where did you source the Surefire 3-prong? Also do you know if the 3-prong works with the blast warden?
Thanks. Any sure fire dealer can get them but it will be a bit of a wait because it’s special order. Yea the blast warden will work
Got my SMR today
Holy #### this thing is tight. I lubed up the barrel nut and still had a hard time installing it. Feels like if I want to clean the gas system, I must take out the cross bolt and fire the rifle a few times for the handguard to loosen so I can take it off.
Holy #### this thing is tight. I lubed up the barrel nut and still had a hard time installing it. Feels like if I want to clean the gas system, I must take out the cross bolt and fire the rifle a few times for the handguard to loosen so I can take it off.
Last edited:
