Ammo ain't cheap but it's available and there are a few commercial hunt loadings available. It's about the same price as 308.
MRA Renegade Rifles, Parts, and Kits now available
- Thread starter Maple Ridge Armourer
- Start date
Ammo ain't cheap but it's available and there are a few commercial hunt loadings available. It's about the same price as 308.
Ohno
CGN frequent flyer
- Location
- Left Coast
6.5 Grendel has similar ballistics to the 243 if you are wondering.
Hornady ELT 123gr @ 2500 fps
Hornady ELT 123gr @ 2500 fps
- Location
- Vernon, BC
If you could please let us know when these plates are available I would very much appreciate it, or I would be prepared to do a pre-order, I would take 3 plates
Thx
AbH
Paul_1982
CGN Ultra frequent flyer
- Location
- Orangeville
I’m eagerly awaiting the .308 model!
Maple Ridge Armourer
CGN frequent flyer
We are making several hundred and we will post here and on our social media when they are available.
On the topic of proprietary magazines, is it possible to make the max COAL support 2.87 inches or longer for the proprietary Maverick magazines if you do decide to go that route? I know some AR-10/SR-25 pattern magazines can fit cartridges up to 2.90 inches COAL; if you can make them that would be amazing.
Maple Ridge Armourer
CGN frequent flyer
Great idea and I dont see why we couldn't do this.
Maple Ridge Armourer
CGN frequent flyer
There is no dust cover on either side.
Not dust cover like the typical dust cover. One that covers dirt and such for when someone has the charging handle on the ejector side. Serves no purpose other than cosmetic covering the unused slit
The 6.5 grendel has way less case capacity than the 243
frojoe
New member
- Location
- North Vancouver, BC
So glad I found this thread... eagerly awaiting the release of the bigger 308 Maverick receiver!
COREY
CGN frequent flyer
- Location
- Ottawa, Ontario
Anyone tried the JP Silent spring in their Renegade? Had a pile of problems with the standard spring installed from the factory today; would not fully go into battery. The spring, barrel, and bolt had all been tested on an AR and worked flawlessly.
Maple Ridge Armourer
CGN frequent flyer
There should be no problem with the factory installed spring. All factory guns are test fired. Please email info@mapleridgearmoury.com and we can help resolve the issue.
- Location
- Vernon, BC
Good morning to the MRA team!
I hope this note finds you all well…
Is there any update to win these plates will be available please I have three bills that required
Thank you for your time and attention to this matter
Warmest regards
AbH
COREY
CGN frequent flyer
- Location
- Ottawa, Ontario
My rifle is one of the receiver kits that I have swapped parts from an AR to get up and running. This was not a full rifle from the shop. That said, it is a Wilson Combat barrel and Daniel Defense bolt tjat mated perfectly before. I am asking if anyone has tried the JP silent spring assembly and if they have had problems.
furet
CGN Ultra frequent flyer
- Location
- Who cares...really!!
Are you ridding the charging handle or letting it snap into battery?
COREY
CGN frequent flyer
- Location
- Ottawa, Ontario
I am pulling it back as hard as I can and letting it go. Same as I do with my pistols.
Silly question but did you remove the gas rings? and I also had an issue with one of my barrels not working on the rifle but seemed to work when installed on a AR upper.
COREY
CGN frequent flyer
- Location
- Ottawa, Ontario
Just pulled the bolt off the AR BCG and dropped it onto the Renegade BC. Am I supposed to remove the gas rings?
Sure hope it is not a barrel issue. Whole point of this thing was to salvage a really good barrel. Thing is worthless to me if it does not work with this barrel.
Sure hope it is not a barrel issue. Whole point of this thing was to salvage a really good barrel. Thing is worthless to me if it does not work with this barrel.
