IN-STOCK: All-New TYPE 81 SR
- Thread starter Tactical Imports
- Start date
Hmm.. somewhat related to this, I had to order mine from FOC today since TI still showing sold out, so I was worried I'd be stuck with whatever fix (if any) they come up with. Think TI would still take a look at mine if it shows up cracked? lol
Looks like youre eating crow lol
FOC that says it all ...
So with all this ban nonsense i had to keep my self busy last few days, stress level is very high and thats not healthy. So i figured id get busy with my prototype replacement stock. I have done few SVD stocks in the past, mostly on CZ 858 platform, so i know the stock will need several points of attachment, normally i would have one bolt going through the pistol grip and the other through the thumbhole in to the back of the receiver (cz858 had room for that). But the type 81 SR is pretty limited as far as options go. so i did the only thing that seemed logical, i drilled and threaded a hole in that metal block that's riveted at the back of the receiver. i drilled it in the center of the groove to avoid any interference with the rivets. It is one tough piece of steel, took me a while to go through it and even longer to thread it. Normally i would give it a bit of an angle for the grip bolt so it pulls the stock forward as well as upward. But in this case i had to keep it straight at 90 degrees, since it was already too close to the back of the grip. As for the wooden part that inserts in to the opening at the back of the receiver, i extended it to provide more meat around the two receiver pins. it also kind of helps as a second point of attachment by hooking on to the receiver.
For the stock material i used birch plywood, and once it was finished i had few imperfections that surfaced in few areas of exposed layers. So i had to use wood filler to fill few effected areas. Although this stock does not have such nice grain like the original wood stock does, it still looks good in person, and will look even better once all the staining and polyurethane coating is done. Here is what i have so far...
Also, i have shot another 200 rounds with the improved original stock and it is holding up great, no cracking of any kind.
For the stock material i used birch plywood, and once it was finished i had few imperfections that surfaced in few areas of exposed layers. So i had to use wood filler to fill few effected areas. Although this stock does not have such nice grain like the original wood stock does, it still looks good in person, and will look even better once all the staining and polyurethane coating is done. Here is what i have so far...
Also, i have shot another 200 rounds with the improved original stock and it is holding up great, no cracking of any kind.
Thanks. I should have mentioned, I did change some dimensions, the LOP is 1/2" longer, cheek height is about 1/4" lower and the grip is longer and wider, with a palm swell and a comfy thumbrest, that also allowed for larger thumb opening in the stock.. very comfortable in every way.
So with all this ban nonsense i had to keep my self busy last few days, stress level is very high and thats not healthy. So i figured id get busy with my prototype replacement stock. I have done few SVD stocks in the past, mostly on CZ 858 platform, so i know the stock will need several points of attachment, normally i would have one bolt going through the pistol grip and the other through the thumbhole in to the back of the receiver (cz858 had room for that). But the type 81 SR is pretty limited as far as options go. so i did the only thing that seemed logical, i drilled and threaded a hole in that metal block that's riveted at the back of the receiver. i drilled it in the center of the groove to avoid any interference with the rivets. It is one tough piece of steel, took me a while to go through it and even longer to thread it. Normally i would give it a bit of an angle for the grip bolt so it pulls the stock forward as well as upward. But in this case i had to keep it straight at 90 degrees, since it was already too close to the back of the grip. As for the wooden part that inserts in to the opening at the back of the receiver, i extended it to provide more meat around the two receiver pins. it also kind of helps as a second point of attachment by hooking on to the receiver.
For the stock material i used birch plywood, and once it was finished i had few imperfections that surfaced in few areas of exposed layers. So i had to use wood filler to fill few effected areas. Although this stock does not have such nice grain like the original wood stock does, it still looks good in person, and will look even better once all the staining and polyurethane coating is done. Here is what i have so far...
Also, i have shot another 200 rounds with the improved original stock and it is holding up great, no cracking of any kind.
Excellent work my man. I'll see about a meet up soon if I can
Does this fix maintain the warranty too?
What do you think!?!? It's game over for 90% of this hobby
So with all this ban nonsense i had to keep my self busy last few days, stress level is very high and thats not healthy. So i figured id get busy with my prototype replacement stock. I have done few SVD stocks in the past, mostly on CZ 858 platform, so i know the stock will need several points of attachment, normally i would have one bolt going through the pistol grip and the other through the thumbhole in to the back of the receiver (cz858 had room for that). But the type 81 SR is pretty limited as far as options go. so i did the only thing that seemed logical, i drilled and threaded a hole in that metal block that's riveted at the back of the receiver. i drilled it in the center of the groove to avoid any interference with the rivets. It is one tough piece of steel, took me a while to go through it and even longer to thread it. Normally i would give it a bit of an angle for the grip bolt so it pulls the stock forward as well as upward. But in this case i had to keep it straight at 90 degrees, since it was already too close to the back of the grip. As for the wooden part that inserts in to the opening at the back of the receiver, i extended it to provide more meat around the two receiver pins. it also kind of helps as a second point of attachment by hooking on to the receiver.
For the stock material i used birch plywood, and once it was finished i had few imperfections that surfaced in few areas of exposed layers. So i had to use wood filler to fill few effected areas. Although this stock does not have such nice grain like the original wood stock does, it still looks good in person, and will look even better once all the staining and polyurethane coating is done. Here is what i have so far...
Also, i have shot another 200 rounds with the improved original stock and it is holding up great, no cracking of any kind.
great job and perfect outcome. thank you. a shame you re too far ...
tar 21 ...
it is not gone ... not leaving me ...
