VV N 160 uses?

Dogleg

CGN Ultra frequent flyer
Rating - 100%
113   0   0
Picked up an 8 pounder of Vitavouri N-160 the other day; almost entirely because it was a good deal. Not sure what to try it in, it seems to be useable in a lot of things, but does it stand out for anything in particular? Never used any VV powxers before, partly because it was seldom available, and I didn’t want to risk liking things I couldn’t get more of😂
 
I prefer it in 7x64 / 160 grain loads. I have three 7x64 rifles and it is the best powder I've tried in them. Good velocity, uniformity, and burns clean. So would suggest it should work well in .270, .280, heavy 30-06, light 7mm mag, etc. Very similar to H4350 / IMR 4831 in my limited comparisons
 
Its burn rate is between H4350 and H4831. So whatever works for these two, will work for Vit 160. Many use it as replacement for IMR 4350 and H4350.
 
It's not a powder which offers great velocity however, it is consistent, especially the latest, their temperature insensitive. I use VV-165 in my 7mm Rem. Mag. and VV-135 in my 9.3x74R.
 
Dogleg, N160 has the advantage of being extremely consistent burning, leading to low ES velocities and harmonics repeatability from shot to shot and isn't bothered much by temperatures, other than extreme heat and cold.

My 338-06 loves it with 225 grain bullets, where it gives the best velocities and accuracy.

Same goes for the 280 Remington with monolithic bullets and cup/core bullets over 140 grains.

It prefers magnum primers, if you have them.

I used it for the 30-06 under 200 grain bullets and it gave the best velocity/accuracy combination there as well.

It's also one of the best powders to use in the 270Win with bullets 140 grains to 160 grains.

My 6.5x55 liked it as well with heavy bullets. In the Tikka T3, powder charges can be increased significantly for much better velocities than the books show, but even the book velocities, which are biased to the m96 type actions are very good with this powder.

VV powders tend to cover a wide range between their types, so it's not unusual to find that it may not be the best for velocities but accuracy is almost always better than expected, because of its incredibly consistent burn from shot to shot.

I know some shooters that won't shoot any other powders than VV and go to great lengths to get it.

It seems to be more available lately, especially online.
 
I’ve got a couple 270s, a 30-06 and a 338 Win that could stand some load tweaking, so I’ll start with those I guess. Got some 560 and 565 kegs coming too, but those I won’t have to wonder what to use it in. Magnums I have lots of.
 
Last edited:
I’ve got a couple 270s, a 30-06 and a 338 Win that could stand some load tweaking, so I’ll start with those I guess. Got some 560 and 570 kegs coming too, but those I won’t have to wonder what to use it in. Magnums I have lots of.
N160 and N560 are almost identical. If anything, the N560 may be even more consistent than N160 and less temperature sensitive.

N570 would be better for your 338WM or whatever. It's to slow for the mid size cartridges, other than with the heaviest bullets available.
 
Check the Lee load data, there’s a fair bit of Vitavouri listed. I was looking for N-150 data for a buddy in 30-06 and there’s a bunch listed for N-160 once you get into 165gr and up bullets.
The Lyman manuals usually have at least one VV powder listed in their tables. Also VV has a free website with lots of load info.
 
The Lyman manuals usually have at least one VV powder listed in their tables. Also VV has a free website with lots of load info.
They do, I sent him pics from Lee, Lyman, Hornady and Nosler load manuals. All had N-150 loads, I think he was looking for 150-155gr bullet info and whatever books he had didn’t list N-150 data. Just N-160 iirc
 
Back
Top Bottom