Maple Ridge Armoury Renegade MKII .223 recipe

Im on a very similar endeavor! Working up a "long range plinking / Varmint hunting" load for my 16" Renegade Mk2.

Chose 68gr Hornady BTHP Match bullets because they seem readily available and priced fair.

Chose Hodgdon Varget because that is what I already have lots of ( and I want temp stability ).

Couldn't find any 68gr data combined with Varget so I used 69gr SMK data. Hodgdons website had a starting load of 22.7 to a compression load of 24.7.

I loaded up a ladder test of 23.0, 23.5, 24.0 (which sounded like a compression load) , 24.5 (which 100% stuck me as being a serious compression load ) .... meanwhile Lymans book maxes out at 26.0 grs ! Lol no thanks Lyman.

The 1 inch stickers combined with what must be a 2 moa dot on my Vortex LPVO didnt seem like a very consistent aiming setup. But I tried the ladder test anyways.

Noticing that as soon as I reached the compression loads the accuracy degraded massively. I fired one of the 24.5gr loads and saw an extremely flattened out primer, extraction felt possibly sticky, but it was barely noticeable. Because of the flattened out primer and garbage grade accuracy from the 24.0gr, I decided to pull the remaining 24.5gr loads.

Im going to explore the 23.5gr charge combined with a better aiming point some more.
 

Attachments

  • 20261111_210614.jpg
    20261111_210614.jpg
    86.6 KB · Views: 11
  • 20260331_224637.jpg
    20260331_224637.jpg
    192.4 KB · Views: 12
I saw this in the Lyman manual as well, but look at your primers, they are no just flat, they are hammered.

Here is what they say on the Hodgdon web site:

View attachment 1238242
I noticed during the reloading process that there's a difference in case capacity between different brands of brass which would lead to higher pressure in some. Likely the ones with the extraction issue. I wonder why different manuals have so much discrepancy. I can see Hodgdon doing it for liability issues, but my velocities aren't crazy compared to theirs. Barrel length might subtract 100fps in my case. Their OAL is lower also by 0.060".

Edit to add...apparently I'm using the wrong primers. I've been using CCI 400 which is not made for .223cal
 
Last edited:
I use the cci 400 small rifle primer in my 223 with no issues
According to the hornady manual for a 55 gr bullet the min charge for Varget is 22.8 and the max is 26.4
The Lymam book says 25 min and 27.8 max but the max is a compressed load
Your groups are good but I’d try a lower charge of powder
 
Mixed-headstamp brass is for plinking. If you're working up an accurate load, start by selecting just a single consistent headstamp!

I also find that with .223 being half the size of other popular rifle rounds, I have to be twice as finicky about measuring charges etc.
 
I used the RCBS small base sizing die and went out the other day. I had my brass catcher on so I don't definitely know that the two rounds thaat were still hard to eject were the two odd head stamps out of ten that I shot, but I'm assuming so. I'll be culling that brass as I move forward.

View attachment 1238181

Using the same 27gr load of Varget with 55gr V-Max bullets and a Trigger Tech trigger gave me some reasonable results. Two 100 yard 5 shot groups. I put up my 200 yard target by mistake so ignore that part of my writing on the target. I called the two flyers on each group so I think this rifle shoots pretty well.

View attachment 1238189
Your spent primers are trying to tell you something.
 
I went out today with the same load and CCI 450 primers. Spent primer pic and head space pic.

450 primers.jpg
Headspace.jpg

Case length is spot on but it looks like I'm at the minimum for head space.
 
Back
Top Bottom