Makasi mk15 initial overview and issues

I'd be more worried if Brigade was delivering too many rifles and letting QC slip to meet the demand.

If everyone just experiences light primer strikes for a break-in period that's tolerable given the lack of options for modern semis.
My order from Marstar just shipped!
 
And those arent “light strikes” in the traditional sense. ...The primer mark is from the free float firing pin just kissing the primer when chambering the round. Pulling the trigger just results in the bolt being tapped that extra “c-hair” into battery with a crispy click.
What? Are you implying all previous feedback was not about actual light strikes? Because in my book a light primer strike happens when you pull the trigger and the firing pin or striker hits the cartridge primer, but without enough force to ignite it. I think your assumption is incorrect - just check the post above mine.
 
What? Are you implying all previous feedback was not about actual light strikes? Because in my book a light primer strike happens when you pull the trigger and the firing pin or striker hits the cartridge primer, but without enough force to ignite it. I think your assumption is incorrect - just check the post above mine.
Im implying that most people dont stare at the bolt carrier while pulling the trigger when diagnosing issues. Every round i have chambered successfully has went bang. Period. Every round that chambers will have a primer mark because of the free floating firing pin. Broke in two rifles myself so far and studied videos of common malfunctions and i can confidently say all of the “light primer strikes” are a result of pulling the trigger when the bolt isnt fully seated. If you dont know what’s going on and arent paying attention a guy could easily chalk up the issue to real light primer strikes when its an entirely different issue.
 
And a light strike means the firing pin is striking the primer but with not enough force. In these cases, especially cause buddy above mentioned lar mags, the bolt isnt seating fully. Hammer strikes the bolt, knocks the bolt and round into the chamber but doesnt strike the primer because of inherent ar safety mechanisms preventing oob detonations.
 
I just received a shipping notice from MARSTAR for my NR Makasi with 12" Handguard. It should arrive here early next week if all goes according to the usual shipping time from ON to AB. The anticipation grows.....
I’m so sad that I didn’t get my pal until recently, would’ve pre ordered but now it feels like there’s no point.
 
I’m so sad that I didn’t get my pal until recently, would’ve pre ordered but now it feels like there’s no point.

Not necessarily! I just placed my order (and paid in full), on the 9th of this month, so just 8 days ago..... and I will receive my rifle in the first draft of 12" Handguard versions to be shipped out. MARSTAR will apparently receive another batch of rifles in 2 week's time....
 
Last edited:
Not necessarily! I just placed my order (and paid in full), on the 9th of this month, so just 8 days ago..... and I will receive my rifle in the first draft of 12" Handguard versions to be shipped out. MARSTAR will apparently receive another batch of rifles in 2 week's time....
This gives me some hope.
If you just got your PAL you may want to look at a rifle that should run fine from the beginning like the Carmel.
I’m most likely gonna get the Carmel, local shop is supposed to get more this week hopefully.
 
Iron Brotherhood on Instagram said they very heavily lubed their Makasi during their first few hundred rounds and did not have light primer strikes. Not sure if it will work for everyone, but maybe worth a try if you are getting a lot of light primer strikes?
^^^ If there are tolerance issues, this is what one would want to do. Lapping compound will turn your rifle to junk in no time.
Run the gun wet, like sopping wet with CLP.
 
And a light strike means the firing pin is striking the primer but with not enough force. In these cases, especially cause buddy above mentioned lar mags, the bolt isnt seating fully. Hammer strikes the bolt, knocks the bolt and round into the chamber but doesnt strike the primer because of inherent ar safety mechanisms preventing oob detonations.
Basically the hammer rides the BGC and does not strike the firing pin in the proper position ( and it should not). This means the hammer strikes before the bolt is fully locked - and the BGC is designed such that the firing cannot be struck and protrude long enough to ignite if bolt is fully locked in. So really in this cases it sounds like the bolt bounces out of the locked in position when hammer strikes ( out of battery) - so it is not a light strike but it s really out of battery and the safety design kicks in.
 
Basically the hammer rides the BGC and does not strike the firing pin in the proper position ( and it should not). This means the hammer strikes before the bolt is fully locked - and the BGC is designed such that the firing PIN cannot be struck and protrude long enough to ignite THE PRIMER if THE bolt is NOT fully locked in. So really in this cases it sounds like the bolt bounces out of the locked in position when hammer strikes ( out of battery) - so it is not a light strike but it s really out of battery and the safety design kicks in.

Exactly. This is what is most likely causing the dented primers - at least until break-in of the Operating Springs is complete and the Bolt-Carrier failing to fully close ceases occurring.
 
Tbh if rdsc cant find what going on with it im likely just gonna trade it for a carmel. Runs pmags and cross mags well enough, lar mags are just a finicky little bastard.
 
May I ask when did you order and did you stay with the 12"?
I had no use for the extra hand guard length. With them confirming that both rifles would get the reliability upgrades and me wanting to run a Faux reverse suppressor it just worked out. Bonus obviously getting it earlier than the 15-inch versions.
 
Back
Top Bottom