I put 150ish rounds through mine for the first time yesterday before I ran out of daylight. Experienced a ton of light strikes. I didn't take apart or clean the bcg at all before I went out but I probably should have, it was a little sticky in there. Its all clean again now so I'm hoping next time will do better. I was getting a disappointing 1-2 light strikes per LAR mag.
When it was working properly it was awesome though!
For anyone who has one of these and expirenced light strikes initially but then they cleared up after a couple hundred rounds can you see any noticeable wear anywhere that occurred in order for the gun to break in?
Just curious as to what has to wear in in order for these to be reliable
The other offering the Carmel doesn’t appear to have any break in required for it to work properly
For anyone who has one of these and expirenced light strikes initially but then they cleared up after a couple hundred rounds can you see any noticeable wear anywhere that occurred in order for the gun to break in?
Just curious as to what has to wear in in order for these to be reliable
The other offering the Carmel doesn’t appear to have any break in required for it to work properly
And those arent “light strikes” in the traditional sense. Thankfully ar bolts have oob detonation prevention otherwise both me and you would have ‘sploded by now. The primer mark is from the free float firing pin just kissing the primer when chambering the round. Pulling the trigger just results in the bolt being tapped that extra “c-hair” into battery with a crispy click.I put 150ish rounds through mine for the first time yesterday before I ran out of daylight. Experienced a ton of light strikes. I didn't take apart or clean the bcg at all before I went out but I probably should have, it was a little sticky in there. Its all clean again now so I'm hoping next time will do better. I was getting a disappointing 1-2 light strikes per LAR mag.
When it was working properly it was awesome though!
I had an OOB with chrypto? If I recall, I believe that used an AR BCGAnd those arent “light strikes” in the traditional sense. Thankfully ar bolts have oob detonation prevention otherwise both me and you would have ‘sploded by now. The primer mark is from the free float firing pin just kissing the primer when chambering the round. Pulling the trigger just results in the bolt being tapped that extra “c-hair” into battery with a crispy click.
This is my first ar style firearm so I'm not too clued in on the whole bolt operation, but that makes sense.And those arent “light strikes” in the traditional sense. Thankfully ar bolts have oob detonation prevention otherwise both me and you would have ‘sploded by now. The primer mark is from the free float firing pin just kissing the primer when chambering the round. Pulling the trigger just results in the bolt being tapped that extra “c-hair” into battery with a crispy click.
Wear gloves lolThis is my first ar style firearm so I'm not too clued in on the whole bolt operation, but that makes sense.
These primers looked the same as the spent casings though so I was pretty confused.
One fellow on Reddit contacted Brigade Mfg. about his intial break-in problems and the manufacturer mentioned that they delivered rifles with BCG's that were known to have tolerance issues. [https://www.reddit.com/r/canadaguns/s/mSfoR33hJb] It's definitely not the only possibility, but the use of lapping compound is now a seemingly effective remedy to accelerate the break-in process.I stand to be corrected, but I believe the Break-In period with the Makasi is mostly associated with the nested Operating Springs taking a proper long-term set. This in turn, eliminates the "bolt bounce" which results in the random, occasional light primer strikes that most Makasi owners experience during the initial 200 rounds or so.
Like I said, I stand to be corrected, but the Operating Springs seem to me to be the primary culprit when it comes to those light strikes during Makasi break-in....
While the Carmel does not require a break-in period for reliable function, it has several other drawbacks which keep me from wanting one. Heavy weight before accessories, pencil barrel, questionable accuracy, zero aftermarket support, proprietary trigger, no ability to upgrade or rebarrel, etc. Oh, and the "chunky/thick" aesthetics don't appeal to me at all.
Looking like dealers are getting them now, Crafm just posted thisMarstar is shipping their first pre-order batch of rifles this coming week. Total number unknown, but apparently not enough to finish pre-orders for the 12" Handguard until they receive a 2nd batch of rifles in 2 week's time. These 12" Handguard rifles are apparently the Gravel-imported guns, FWIW. View attachment 1240169

I'm assuming these are all 12" models...?Looking like dealers are getting them now, Crafm just posted this
View attachment 1241183
I believe soI'm assuming these are all 12" models...?



























