Savage Stevens 200 Review or "The Poor Mans Precision Rifle"

Travis Bickle

CGN Ultra frequent flyer
Rating - 100%
179   0   1
Well about 3 months ago I decided I wanted to get out of my primarily milsurp addiction and get a scoped precision rifle.
However, I wanted to build a set-up that wasn't going to destroy my bank account. I try to keep my shooting hobby to a very frugal limit.

So my requirements were:

1- The rifle had to be inexpensive.
2- The caliber had to be very inexpensive.
3- It had to be a bolt action.
4- It had to be very accurate.

I did much research on the topic.
Eventually after reading a lot of U.S. gun forums I settled on a Savage Stevens 200 in .223 Rem.

So I set out to find one in bare bones stock condition. I'm so damned cheap I even found a second hand brand new condition one vice paying retail.
Cost for the rifle with no optics $280.

I then wheeled and dealed a little and traded some old stuff I had kicking around for a used folding Harris bipod. Cost: $0
I then hit the EE for a used Bushnell Trophy 3 x 9-40 scope Cost: $80

Next the mount.
I picked up an EGW picatinny round back rail. Cost $30.00

The mount/rings I picked up in the states. Again, I got this item in a trade so total cost again: $0 However, I could have easily just bought two rings for about $40-$50.

Total cost to me: $390.00

I assembled the items to the rifle.

The result:

P6100335.jpg


I took it out today to the bush. After driving off a track to my favourite less known spot. I paced out 100 meters. 140 steps with my stubby legs :D

I fired all shots from the prone using the bipod and nothing else.

Ammunition was old '82 bandolier Canadian surplus in average condition.

After a couple of wingers and the barrel heating up a little, the groupings started to dial in a bit.

The fit and finish of the rifle is great.
The trigger pull is very light.
The Stevens bolt is a little overcomplicated for my simple pragmatic tastes but the accuracy of the rifle more than overshadows this.
The action is very smooth and chambers rounds very easily.
However the single stack box magazine is a bit of a ##### to load. Especially with the optics on the rifle.
It's much easier to just chuck a loose cartridge into the breech and pick it up with the bolt one at a time.
The stock is not pretty, it's a hard durable polymer in a camo green. It's ugly, it's rugged and it works.


I shot 3 very impressive groups for such a cheap "out of the box" bare bones rifle.

Again all shots from 100 meters in the prone using the bipod.

Here is the first good 3 shot group aiming for dead center, the coin is a Canadian dime:

P6100324.jpg


Another 3 shot aiming for the "8", again with a dime for reference:

P6100330.jpg


This 5 round group was all 5 shots as fast as I could accurately shoot. I learned something important about my fundamental shooting abilities today, I actually shoot more accurately when I take less time to focus on my shots! :confused: Albeit I tend to apparently shoot high and left when I take less time lol:

P6100332.jpg


In the end though, what I have found is that the Savage Stevens more than lived up to it's American reputation as being an incredibly accurate and extremely functional and reliable "out of the box" rifle for a very low cost.

I can only imagine what a trigger job, a heavy barrel and some quality, non surplus, or even hand loaded rounds could do, bedding the action or mounting some stupid expensive optics but again all that would defeat the purpose of my initial personal challenge of building the poor mans precision rifle.


All these factors has allowed me to personally rate this rifle as having incredible value for the price.
And all this considered has earned itself now the title of:
DISCOUNT SNIPER C1A1 :rockOn:

Some more pics of the ugly little discount rifle that could :D

P6100336.jpg


P6100334.jpg


P6100338.jpg


And just because this is CGN, a picture of my vintage minty Stevens 311A
12 ga which I use for BEAR DEFENSE when out in the deeper bush :D

P6100326.jpg


Cheers!
 
Your scope sits a lot higher than it needs to. It might be easier to shoot with low rings directly mounted to the rail.
 
Got one in .243. Love it. Been using it as my main hunting rifle for the last 4 years. Deadly. It has a Tasco Mildot in 2.5X9 over medium(#44 if I remember) Millet rings.

DF:D
 
Luck guy.... I had to do a lot of tinkering to get my Stevens to hold 5 shots around 3/4-1/2 MOA with hand loads and yours is doing it with some old ball ammo and unbedded? Yikes!
don't change anything :D

Great bang for the buck rifle.... That reminds me, I need to start looking for one in .308!
 
Luck guy.... I had to do a lot of tinkering to get my Stevens to hold 5 shots around 3/4-1/2 MOA with hand loads and yours is doing it with some old ball ammo and unbedded? Yikes!
don't change anything :D

Great bang for the buck rifle.... That reminds me, I need to start looking for one in .308!

After trying to squeeze non existant accuracy out of a crusty old iron sighted Mosin Nagant for so long, shooting with a scoped rifle seemed so easy it almost felt like cheating lolol

I must say though, it is very addictive! :D
 
I hear ya, went open irons to peeps, peeps to old 4x Mauser scoped. The that to rem 700 with 6-24x50 4200 bushnell elite.
 
i have one in 308. total cost to me was 500. gun was 250 and scope with mounts were another 250. it shoots great with win white box around 1 inch at 100 yards. action is smooth and is a great project gun.
 
i have one in 308. total cost to me was 500. gun was 250 and scope with mounts were another 250. it shoots great with win white box around 1 inch at 100 yards. action is smooth and is a great project gun.

Agreed!

It's going to be hard to keep this as a "poor mans" rifle and not start sinking sickening amounts of dollars into it lolol

Truly a test of my will power V:I:
 
Put it this way, my Stevens started out like yours, Travis. Now it has a Shilen barrel and a Boyd's stock and it doesn't shoot any better than yours. Don't bother putting more money into it. It's a great gun as is.
 
My Tikka T3 Lite in 30/06 will shoot sub 1" groups at 200 yards with Barnes TTSX bullets. But guess what? IT IS A HUNTING RIFLE NOT A PRECISION RIFLE!
 
Agreed!

It's going to be hard to keep this as a "poor mans" rifle and not start sinking sickening amounts of dollars into it lolol

Truly a test of my will power V:I:

yes i just got back from shooting mine at my private range, was using some cheapo norinco ammo and was getting junst under an inch to 1 1/4. great gun. i think im going to get a better stock for it and better trigger. then get the barrel threaded and get a brake made for it.
 
Put it this way, my Stevens started out like yours, Travis. Now it has a Shilen barrel and a Boyd's stock and it doesn't shoot any better than yours. Don't bother putting more money into it. It's a great gun as is.

That's what I was hoping lol I guess I picked the right foundation.

This is my first "precision" rifle.

I'm going to have to track down some higher quality ammo. I don't reload yet.

Does anyone have any recomendations for a decent commercial .223 Rem?
 
I believe Federal makes their Gold Medal Match ammo in .223, that's sort of a standard precision load. You'll see a lot of new rifles shooting this ammo as a decent test of accuracy because it seems to be pretty consistent. However, handloads will let you tune to your gun, as you mentioned.

Keep it simple for this one man. I'm more than slightly pissed to see your gun shooting better groups than mine... Even after I've dumped $$ on a sweet barrel.

Invest in optics, as you can move optics from gun to gun.

Plus, with this fun gun, if you drop it in the woods, you won't care. I'd weep violently if I gouged a chunk out of my Shilen.
 
Once I burn this barrel out (and I will with the amount I shoot :D) I was planning on getting a heavy/bull barrel to replace it.

Are they easy to acquire?
What are the prices for one?
Who carries them? Would I have to contact Savage?
 
Once I burn this barrel out (and I will with the amount I shoot :D) I was planning on getting a heavy/bull barrel to replace it.

Are they easy to acquire?
What are the prices for one?
Who carries them? Would I have to contact Savage?

Here are two CGN sponsors that supply Savage heavy barrels:

http://www.mysticprecision.com

http://www.northshorebarrels.ca
 
Once I burn this barrel out (and I will with the amount I shoot :D) I was planning on getting a heavy/bull barrel to replace it.

Are they easy to acquire?
What are the prices for one?
Who carries them? Would I have to contact Savage?

Aftermarket or from savage?

savage take offs are on the EE a fair bit.

I have a 20" shillen pre-fit bull barrel with 1:9 coming from jerry @ mystic. cost more than the rifle :eek: , but very painless. just an email away.
 
Yeah my barrel is a Shilen acquired trough Mystic as well. Prices are on his site.

Swapping barrels is really easy on a Savage rifle. Savages have a barrel nut, meaning you can headspace your barrel yourself, and then tighten the nut when you've found the right spot.

Remingtons are more difficult because they don't have the barrel nut design.
 
Back
Top Bottom