Your 3-Gun Rifle Setup?

New to this, only shot one Match so far

Knights Arms SR-15E3 IWS CARBINE MOD1 - love this, my first and likely my last .556 AR
Eotech XPS 3 with magnifier but just ordered the Vortex Viper PST 1-4
Pistol has not been decided on quite yet, shot my CZ Sp01 Shadow for the first match with good results but have a Glock 35 on the way as well
 


Sabre Defense lower.
American Gold trigger.
Phase 5 Bolt-stop/lever.
ACE SOCOM stock.
Ergo pistol grip.
JP upper, 18" light profile SS free floated barrel with adjustable gas block and brake.
Low mass bolt carrier with JP's silent captured buffer.
Scope is a Leupold Vx-6 1-6x28 in a 30mm Warne one piece mount.

Makes for a very light, shootable rifle...
 
updated with recent mods

Bushnell Elite 1-6.5 in a Larue SPR-E QD mount
CTR stock
ERGO grip
DD upper with JP LMOS BCG & Raptor Charging handle
STI lower with JP trigger springs (a simple cheap and crisp 2.75# trigger)
18" JP medium contour FF barrel, Adj gas block, heat sink and comp
Magpul ASAP single sling point adaptor
Also have QD sling adaptor on the opposite side of the handguard to allow for a two point setup with the CTR stock

011_zps456e8eee.jpg
 
Last edited:
I've seen this photo before....do you have a wide angle lens on that camera?

667 said:


Sabre Defense lower.
American Gold trigger.
Phase 5 Bolt-stop/lever.
ACE SOCOM stock.
Ergo pistol grip.
JP upper, 18" light profile SS free floated barrel with adjustable gas block and brake.
Low mass bolt carrier with JP's silent captured buffer.
Scope is a Leupold Vx-6 1-6x28 in a 30mm Warne one piece mount.

Makes for a very light, shootable rifle...
Click to expand...
 
Onagoth said:
I've seen this photo before....do you have a wide angle lens on that camera?
Click to expand...

'Borrowed my kids fancy schmancy camera. She's got 3 lenses... I told her what I wanted to snap and she set it up for me...
beyond that... I dunno.
 
TRaTSeRiF said:
Possible to take the pic from a distance and then just crop it. As long as the lighting is good and got plenty of megapixels, you can make it look good.
Click to expand...

You can shoot it from a distance, which is exactly what I did in my photo....but his in on a much higher magnification, which is why i suspect is a wide-angle lens.
 
1175624_622063314492467_2093710386_n_zps84f88204.jpg


Rifle upper is what i used all last year. Built by myself. McGowan barrel from Mystic, JP internals, Vltor upper, Surefire brake, Elcan Spectre DR. Lower is not what I normally run. I use an ACE rifle length stock with JP captured spring and Timney trigger. Bought used so I may stay with AR Gold as in picture but kinda want to try a Hypertrigger.

Shotgun is Benelli M1S90 SS that has a TTI bolt, trigger job, Nordic stuff, bolt release is I can't remember, and personal modifications to the receiver for deuces.

Pistol was Glock 34 with Dawson sights, CCW magwell, Vanek GM model trigger.
 
Rifle:
Colt A2 20"HB
Primary Arms 1-6x
JP comp
PMAG Gen2 30rd (x4)
PMAG Gen2 30rd with Nordic 18rd extension (x1)
Surefire 60rd (x1)
Wilson Twinmag 20 - two 20's coupled (x1)

I'm looking to replace it with either the Colt CR Expert or a Stag Arms M3G

Shotgun:
Beretta 1301 Comp
Nordic +4 tube
HiViz TriComp FO
AP Custom Shotshell carriers L2/6 (x2)
California Comp Works 6rd Speed Stripper (x2)

Pistols:
H&K USP Custom Sport 9mm
H&K Magwell
H&K 18rd 'white mags' (x4)
or
CZ Custom Shop SP01 Shadow Custom
CZ 18rd mags (x3)
 
7.62mm said:
How are you liking the 1301 Comp?
Shot a demo gun at FNH last year, but kind of hard to get a feel for it when you only put 5 rounds through it.
Click to expand...

I like it. I've only used at 2 local matches so far. It's light and so is the recoil. < $1000 USD shipped for the 21" Nobody can keep the 24" in stock as they look better with a longer tube.

I don't have a lot of SG experience. My last SG was the 870 Express SuperMag I shot at EESA 3 gun a few years ago.

Comes from the factory with the loading port opened up, low drag follower, oversize release and oversize safety. The lifter doesn't need welding (unless your thumbs are VERY small). The only thing I've done is the Nordic tube to give me 9 + 1, and the HiViz front sight.

Guys tell me it likes anything, but I've found (and so have others) that the WallyWorld bulk Win is shyte. It turns your nice semi into a bolt gun. Win AA's ran great. S&B sport slugs no problem.
 
D_ said:
Rifle upper is what i used all last year. Built by myself. McGowan barrel from Mystic, JP internals, Vltor upper, Surefire brake, Elcan Spectre DR. Lower is not what I normally run. I use an ACE rifle length stock with JP captured spring and Timney trigger. Bought used so I may stay with AR Gold as in picture but kinda want to try a Hypertrigger.

Shotgun is Benelli M1S90 SS that has a TTI bolt, trigger job, Nordic stuff, bolt release is I can't remember, and personal modifications to the receiver for deuces.

Pistol was Glock 34 with Dawson sights, CCW magwell, Vanek GM model trigger.
Click to expand...

Is that the taccom shotgun release tab? If so, does it work OK?
 
It looks like a Daves Metal Works tab vs the taccom.
The ones taccom sells are made by Redneck Tactical

I've used similar and it works.
Only thing I didn't like was the fact you jam it under the forend, and it can catch on your palm if you do a really crappy reload (I mean really crappy...your hand shouldn't even be over there, but it happened, learn from this experience, type of reload)

But its non-permanent and does what its supposed to do
 
You must log in or register to reply here.
Back
Top Bottom