10/22 photos - post 'em up here!
- Thread starter mchaley
- Start date
Finally built my dream 22.
Tuff-22, 12.5" Dlask carbon barrel.. Kidd bolt, extractor, springs and internals, Kidd 2 stage trigger and extended mag release.. Magpul hunter stock, Nightforce 1 piece scope mount and a Viper PST.. Bare rifle weighs a whopping 5.7 pounds, and 29" long.
The trigger is quite incredible.. I have it at 6 ounces per stage, it's like nothing I've experienced.
20210309_202657 by Joshua Skelton, on Flickr
Tuff-22, 12.5" Dlask carbon barrel.. Kidd bolt, extractor, springs and internals, Kidd 2 stage trigger and extended mag release.. Magpul hunter stock, Nightforce 1 piece scope mount and a Viper PST.. Bare rifle weighs a whopping 5.7 pounds, and 29" long.
The trigger is quite incredible.. I have it at 6 ounces per stage, it's like nothing I've experienced.
20210309_202657 by Joshua Skelton, on Flickr
Recently acquired "new to me" stainless 10/22 in factory plain blk synthetic stock:
Dropped into nice laminate that I had kicking around. Replaced scope rings with matte blk ones:
-----------
NAA.
Dropped into nice laminate that I had kicking around. Replaced scope rings with matte blk ones:
-----------
NAA.
Last edited:
Just put this one together as the barrel just arrived from Brownell's. I wasn't planning anything, it just sorta happened. I bought MCarbo trigger springs and polished the internals, replaced the crappy Scorpion scope with an alright Vortex Crossfire II, replaced the crappy Scorpion rings with alright Vortex Hunters, put an ER Shaw barrel on it and dropped it all into a Magpul Hunter. This was just a beauty shot, not bore sighted yet as I ended up sliding the scope forward a bit after getting my 13-year-old to test fit it all. So now it fits me better, too! Range day on Thursday.
Midwest Industries Fixed Barrel chasis 13"
Midwest Industries Picatinny Rail
SR-22 Receiver and bolt
Factory trigger
DLASK 16.5" heavy barrel (.920)
KIDD Charging Handle
KIDD Recoil Spring and Polished Guide Rod
Pinned BX-25 mag
*and a bunch of take off AR parts
Midwest Industries Picatinny Rail
SR-22 Receiver and bolt
Factory trigger
DLASK 16.5" heavy barrel (.920)
KIDD Charging Handle
KIDD Recoil Spring and Polished Guide Rod
Pinned BX-25 mag
*and a bunch of take off AR parts
snip/
A couple custom compact internationals I put together.
Oh...shouldn't have shown me those...
My first 10/22 that I've been slowly upgrading over the past four years or so.
-Hogue Over Molded Stock
-Volquartsen Target Hammer, Firing Pin, Extractor and Auto Bolt Release
-TSR100 Tech Sights
-Extended Mag Release off Ebay
-Tandem Kross Takedown Knob
-USGI Sling
Gets about 3 MOA with CCI SV in my hands so nothing special but it's the funnest gun I've owned so far and has seen over 10,000 rounds with hardly a hick-up!
https://m.imgur.com/hwMnLpO
-Hogue Over Molded Stock
-Volquartsen Target Hammer, Firing Pin, Extractor and Auto Bolt Release
-TSR100 Tech Sights
-Extended Mag Release off Ebay
-Tandem Kross Takedown Knob
-USGI Sling
Gets about 3 MOA with CCI SV in my hands so nothing special but it's the funnest gun I've owned so far and has seen over 10,000 rounds with hardly a hick-up!
https://m.imgur.com/hwMnLpO
Last edited:
