1904 sxs shells

Rivers sxs

New member
Rating - 0%
0   0   0
Hi guys I’m really new to old sxs and I just bought a piece of history and need some help for low pressure ammo and where is best to buy online ?
Cheers mike
 
You may have to roll your own. I start with Federal paper shells and trim them about 1/4 of an inch. I resize and then load them with BP, over powder card, fiber wad, shot ans over shot card. I finish with a roll crimp. I found the required tools at a gun show. You need the following: trimmer, resizing tool, decapper/primer seater, a scale to weigh powder and shot, a dowel to push down the cards and wads, and a roll crimper. Total cost was less than $100 for the tools.
 
I noticed some lots of 2.5" 12 ga. shotshells in the next Lansborough auction. Some are black powder factory loads and some are low pressure smokeless. Shipping is a killer but your LGS may be able to order in RST or Gamebore low pressure shells. Where are you located? (and tell us about your piece of history)
 
I will be a little careful if I was you.

please listen to an old fool like me

contact Claudio o here and pay him to check firstly if it is still in proof and secondly check barrel wall thickness

please be careful.
 
Proof standard before the First World War is from a different galaxy.

Exactly words of Roger Hancox current proof master of Birmingham proof house to me....

‘ANYTHING GOES”

check before you shove something down those pipes.

It’s a mistake you will not make twice.

if you had said post First World War I would have kept my mouth shut.

I was the duty range officer when a young member blew his face open doing exactly that.

The police checked his computer afterwards and found he got reloading advice off shooting forum.
 
It’s getting checked in a few weeks unless your guy is on the island ?
and the store has checked it all over.
It’s in great condition for age. So I’m not to worried
 
Yes I am been dumped here by my children .... navigating your wonderful country in a right hand drive car oops sorry bolt handle I mean
 
Yeah no problem mate I am new to sxs I read a lot of books but no real experience in the field. I couldn’t afford to buy the one I wanted for a wile but picked up a Parker DHE 12g with titanic steel barrels
 
I have a double barreled Damascus steel barreled side-by-side with exposed hammers that I reload "black powder" shotgun shells (really Pyrodex) for. I watched a lot of Youtube videos, made my own "pound and load" system to trim (x-acto knife), deprime (nail), reprime (manually), then "square load" (equivalent volume pyrodex and shot) with 3/4" round cardboard stock (used a craft hole-punch from Amazon but I hear Michaels sells them). I then glue (white glue) an overshot card on top of the shot.

Depending on the load, I will often use a wad of paper towel as a shock wad between two pieces of cardboard stock (over the powder and below the shot).

Used it a few lines of trap with this shotgun and my own reloads. Fun! Plan on taking it rabbit hunting soon (or as I like to say, take my shotgun for a multi-hour walk through the woods and shoot nothing).

(YMMV, standard disclaimers apply. Reloading is dangerous and no one should do it without blah blah blah)
 
No, I do want to be there.

safest place is up a tree with my rifle , silencer, thermal and ration of curry and beer.

I can be up there for weeks and be socially responsible.
 
Nice mate that’s what I want to start doing I’ve been reading RST shells are good but can’t seem to find them. I was going to use ammo at the 6000psi mark
 
Wonderful

I use to lease a forestry commission land near Braintree , also stalked frequently around Chelmsford

bashed thousands of rabbits around Epping forest

teaming with deer , they must be over populated this season because not many stalkers have been out.

we need to do our public duty .....
 
Nice mate I’m from Rayleigh near southend I was a arborist and still am. Wanted to shoot back home but could never find land to shoot!
 
Back
Top Bottom