20 gauge pump
- Thread starter Leavenworth
- Start date
browninggold
CGN Regular
- Location
- Essex County, Ontario
^this
I also like Mossberg 500s and my favorites (these days) are the older Lakefield/Mossberg pumps. They feel right. I've never owned a 20ga Wingmaster LW but have always wanted to. Had a large frame I should have kept-that gun seemed to find grouse for me.
I have just sent one in the factory box with maybe 3 boxes of shells thru it to precision optics to consign also have a 1969 and 1977 in the 20 gauge magnum These are great guns but I was afraid to scratch this one as it was so nice .
browninggold
CGN Regular
- Location
- Essex County, Ontario
I hear ya, have a 26” and 28” both still NIB…cant bring myself to put a scratch in them
Remington hasn't made a 20 gauge on a 12 gauge frame in decades and they aren't that common. I owned a 20 gauge 870 Skeet in the heavier frame as well as a Wingmaster on the smaller frame in 20 gauge and the lighter frame made a significant improvement in handling.
You can tell a 20 gauge 870 built on the larger frame by looking at the barrel where it meets the receiver. The barrel has a slight taper on the large frame which is not present on the lightweight frame.
You can tell a 20 gauge 870 built on the larger frame by looking at the barrel where it meets the receiver. The barrel has a slight taper on the large frame which is not present on the lightweight frame.
Your right My wingmaster magnum 1969 and 1977 model are both large frame the 2017 is for sure the small frame and barrels are different.
For sure, but they pop-up in the EE several times a year and not all listings point-out the difference. I bought my LF in a store and couldn't believe how good the condition was for the price. It was only when I was checking out they said "oh btw, might be hard to find spare barrels for this gun" We paused/I got an education.
I think I've held and LW only once-loved it.
- Location
- Western Manitoba
Top is 12 gauge BPS - 3" chamber; Invector choke - 22" barrel - serial number suggests made in 1988.
Center is 20 gauge BPS - 3" chamber; fixed **- choke (probably Improved Cylinder) - 26" barrel - serial number suggests made in 1985.
Bottom is 28 gauge BPS - 2 3/4" chamber; Invector choke - 28" barrel - serial number suggests made in 2020.
Leavenworth
CGN frequent flyer
- Location
- Lowermainland B.C.
I know I’m probably getting picky here . But I think I would like the 20 gauge shotgun to have a vent rib barrel and again swapable barrels
sillymike
CGN Ultra frequent flyer
Probably a silly (slightly off topic) question... But does anyone (other than the sporting clays/trap/skeet crowd) actually swap barrels?
Over the years I bought (and sold) a few guns that I had bought different barrels for... But it was more for the curiosity of it.
Over the years I bought (and sold) a few guns that I had bought different barrels for... But it was more for the curiosity of it.
- Location
- Western Manitoba
Some years ago, I had a Stoeger (?) SXS set that had 28 gauge and 20 gauge barrels. I currently have a "spare" barrel for my Winchester Model 12, but I have never fitted or installed it. I have sawed off a few barrels to shorten them from new - that usually required a new front sight or bead to be installed - but other than those mentioned, I do not recall any that were here that had more than one barrel. Even chokes - I understand some people think that interchangeable choke systems are a good thing, but I have never carried alternates with me - what is in the gun, is what it gets fired with - although I suspect some target shooting or clay games might have me swapping chokes, on the go. For OP's information, the BPS's that I have and have had, had the raised vent rib - perhaps 1/8" or so higher than the top the receiver, and removing the tube magazine cap allows the barrel to be removed - so I imagine "swapping" out a barrel would be pretty start-forward. My 12 gauge BPS has a sling swivel stud into that front magazine cap - I use a Butler Creek "mountain sling" with that one.
Most shotgun barrels that I sawed off ended up with no constriction - "Cylinder" choke (?).
That 20 gauge BPS that is here - 26" barrel - fixed choke - stamped **-, so probably Improved Cylinder choke:
A quick measurement with vernier calliper suggests that vent rib is slightly less than 0.2" (5 mm) above the receiver and slightly more than 0.3" (8 mm) wide.
Most shotgun barrels that I sawed off ended up with no constriction - "Cylinder" choke (?).
That 20 gauge BPS that is here - 26" barrel - fixed choke - stamped **-, so probably Improved Cylinder choke:
A quick measurement with vernier calliper suggests that vent rib is slightly less than 0.2" (5 mm) above the receiver and slightly more than 0.3" (8 mm) wide.
Last edited:
I swap barrels on guns quite often. A303 beretta 2.75" chamber for skeet then to a 3" chambered barrel for hunting
Remington 1100 I have several barrels
Mossberg 535 slug barrel for 28" smoothbore
I even swap barrel sets on a vintage sxs Damascus set with short chambers to fluid steel set with 2.75" depending what I'm hunting or what shells I have more of on hand
Leavenworth
CGN frequent flyer
- Location
- Lowermainland B.C.
Another question . Any of you fellas shoot a compact or youth model of 20 gauge and how does it fit you ?
I know it’s all about how it fits the shooter .
I’m average height 5’10”
I know it’s all about how it fits the shooter .
I’m average height 5’10”
Pic of the 20g LW 870 DU that has never been fired. The 1100 below it has 2 barrels one skeet and the other mod screw in choke but it was before Remchoke so is an odd ball .Was not willing to send it in to be copied for fear of ending up with nothing so opted for the skeet barrel.
