AR-15's

[Deckard]

One more- how much?

 

[sithinside]

One more- how much?

Haha, I should get some commission for this...

They range from 180-230 depending on length.

 

[Deckard]

Thanks.

 

[Death]

Sith are your multicam pieces hydrodipped?

 

[Danimal247]

Nice build dude! How's the multicam done?

New upper build pic...

ATRS 14.5", 5.56, 1:7 twist
Battlecomp 1.5
13" VTac forend
Troy low pro gasblock
Stag upper
NEA enhanced BCG
Troy battle sights

Planning on test firing on Wednesday and will be going up on the EE - took over 10 months to build this, and now I need to recoup some expenses.

 

[sithinside]

Sith are your multicam pieces hydrodipped?

Nice build dude! How's the multicam done?

Yup, dipped by a sponsor on the board here from BC - Cobra Imaging

 

[D-BOMB]

Where did you get the 13" alpha rail?

 

[sithinside]

Where did you get the 13" alpha rail?

Like I said above, the Troy Alpha rail is a branded as VTac and Milarm in Edmonton is an official dealer and can bring them in.

 

[Deckard]

Does Cobra do upper and lower receivers too? I can't get them to reply on that question. Thanks again.

 

[sithinside]

Does Cobra do upper and lower receivers too? I can't get them to reply on that question. Thanks again.

Yup, they can dip anything pretty much. Aluminum, polymer, ceramics, etc...

Check their gallery, they have done lots of complete dips.
http://www.cobraimaging.com/

Although, on the front page there is a very strange message saying they're not doing any more work? Seems strange... I got my parts dipped a few months ago...

 

[Deckard]

That does explain things a bit. I wonder how long that will last. I'll do the same project as you if you haven't surmised.

 

[ShrtRnd]

I went digging last week before this post. Answer & at least one alternative can be found below

Cobra Imaging

 

[sithinside]

That's too bad. I've seen some pictures of multicam from that place in red deer - liquid customs - and it looks pretty good too.

 

[Dyspnea]

My upper is nearly complete, major parts are tested fitted. Deciding if I want a 10 or 11 inch forend, I'm liking the look of an 11 inch forend better.

 

[Conte]

That's clever.

I think I'd go 10" myself, I like a bit of exposed barrel.

My upper is nearly complete, major parts are tested fitted. Deciding if I want a 10 or 11 inch forend, I'm liking the look of an 11 inch forend better.

 

[sithinside]

Best 11" forend? Noveske NSR 11"r from Armtac.

 

[Leibermuster]

Best 11" forend? Noveske NSR 11"r from Armtac.

Yeah I second that, Armtac rocks man...

 

[Wantabe_ Warrior]

I'd go with the 10" rail. I'd like to try a Noveske NSR rail, but I like the idea of "45 degree" rails that the Troy Alpha rails offer, and the Troy stuff is a bit cheaper generally.

 

[Dyspnea]

I'd go with the 10" rail. I'd like to try a Noveske NSR rail, but I like the idea of "45 degree" rails that the Troy Alpha rails offer, and the Troy stuff is a bit cheaper generally.

I've been looking into the troy line, they have the style I like plus the pricing isn't too bad.

The noveske rail look great too but at $300 it's a little out of my budget at the moment.

 

[Dmitri]

Best 11" forend? Noveske NSR 11"r from Armtac.

+1, i Agree..