Beretta PX4 Range report

Rivalen

CGN frequent flyer
Rating - 100%
57   0   0
Location
St-Hubert, Qc
Hey there,

Last week I went to the range and tried a rental Beretta PX4 Storm. To compare it to the G17 which I rented the week before, the Beretta felt better in my small hands. It had a better trigger imo than the 2 other gun I tried (USP9 and G17). If felt a lot smoother and crispier. The first SA shot really surprised my as I wasn't aware it would fire so early.

I really liked the DA/SA (Although my DA shot were pretty bad). I fired using the same grip and stance as I did with the G17, but the recoil was much more pronounced on the Beretta. I wonder why? Gun balance? Higher bore axis? Lighter gun (I doubt it)?.

Anyway I pretty much enjoyed the pistol, the only think I didn't like was the manual safety on the slide. I'm not a big fan of that. I have a question about it though, if I load a mag in the pistol and rack it with the safety off, the pistol stays in SA. At some point, I put the safety back and it made the hammer drop. It really surprised me; It didn't fire (and I was pointing in a safe direction). I would guess the firing pin is blocked at that point?

Here is are my first 20 shots with the pistol, my first shots were somehow better than my lasts (2 shots to the left are DA ;)):



I'm still in the hunt for "the one", I would say right now, if I had to buy a pistol, it would be the G17 since it worked well the first time I tried it. I could only imagine the results I would get with some serious training :)

Please take note that all the pistol I tried were rentals, so the milleage may vary :cool:

I have yet to put my hands on a SIG P226 which is a pistol i'd really like to try before I decide to buy (can't find anyone with one and shop never has any in stock :()
 
I'm only familiar with the PX-4 type F, but it has a decocker built into the safety. When the hammer is down and you engage the safety, it drops the hammer with the firing pin blocked. If you look at the rear of the gun when engaging the safety you can see a little bar flip around.
 
My response has to be one-sided as I haven't tried a PX4. I did rent about six different SIGs before I decided to buy two of them. Most P226's have a decocker which sounds like what you experienced. You will find a difference in the all steel models in terms of control and felt recoil. I have tried a Glock and much preferred the SIG's. I'm a newbie myself and get the impression that handguns are a bit like women :) Bonne Chance.
Ex Quebcois
 
Is it true the feed ramp is polymer on these? Anyone have pics?

p1040509new.jpg
 
I think the F model also has a half #### safety feature as well so you don't have to carry the pistol with the hammer resting on the safety. You can download the manual from the Beretta website.

I tried the F model and liked it a lot. Very accurate and light recoil. Lots of fun.
 
Thanks! Now my next question. Does it matter?

Well, if you go over to Berettaforum and ask them they always say it's a perfect design and might have been touched by God himself.

Myself, I think it matters. There's a few YouTube PX-4 reviews and some of these guys out there complain about it. Apparently you have to sand it down every couple hundred rounds or so and it's supposed to smooth it out.

I had one and wasn't impressed, so I sold it.
 
Bought one in June, was on my list for some time, I like the look, I was interested in the rotating barrel and I was looking for another 9 mm so I took it home for my birthday.

Feels and handles differently then my GLOCK 17, which is great I didn’t want another clone 9mm.

Shoots well, accurate and light recoil (The rotating barrel does make a difference), I like it.

A bit pricey compare to others pistol but a worthy addition to my collection.

On the plus side, extra mags are only $40 (HK & SIG owners know what I mean)

As for the feeding ramp, it is heavily supported by the feeding “lips” on the barrel.
Some even say that the feeding ramp is on the barrel, In a nutshell nothing to worry about.
 
Back
Top Bottom