CANSOF IUR Clone thread
- Thread starter FoxAlpha
- Start date
Pic of my build... so far. Next comes the paint
Sweet! Nice job Brad.
I used one of the 11.6 MRR barrels in its original configuration, at least for now.
Great Clone!
I do find it interesting CSOR adopted this configuration, it is near identical to the SAS IUR, minus the barrel length and recoil lug for the gl, (11.6 is better for dwell time)
The lowers are the same, down to the ergo grip and asap.
Fuzzy Wool Hat
Regular
- Location
- Ontario, Canada
i wonder why they’d go with the asap endplate. It seems like there’s many better options. But from what I’ve seen, the Canadian users seem to have a lot of freedom when it comes to customizing their own weapons.
![-[Crosshair]-](/forum/data/avatars/m/31/31565.jpg?1718745216){kind=avatar}
If you're part of CANSOF, sure.
Fuzzy Wool Hat
Regular
- Location
- Ontario, Canada
They’re generally the ones using the CANSOF C8 IUR, yeah ��
PaveHammer
CGN frequent flyer
- Location
- Kingston, ON
ASAP adapters work well and are commonly available on Magpul standing offers, just like the RSA. The sling hardware Magpul produces is some of the best around, in my opinion. QD swivels can fail, and often do.
The ARMS front sight has been replaced by Troy M4 BUIS in FDE almost across the board. The ARMS rear is fine, but the front is ####ing junk.
Otherwise, yeah, individual components seem to be swapped out a lot, based on photos from across the net. Some guns appear to be in Operator hands, some appear to be in Supporter hands, so it's hard to nail down what's at the bleeding edge.
Bradley
The ARMS front sight has been replaced by Troy M4 BUIS in FDE almost across the board. The ARMS rear is fine, but the front is ####ing junk.
Otherwise, yeah, individual components seem to be swapped out a lot, based on photos from across the net. Some guns appear to be in Operator hands, some appear to be in Supporter hands, so it's hard to nail down what's at the bleeding edge.
Bradley
Fuzzy Wool Hat
Regular
- Location
- Ontario, Canada
They usually don’t come with anything
What kind of upper is that?Pic of my build... so far. Next comes the paint
vickers vanguard
CGN Regular
- Location
- Laval, Quebec
Great news...could you update this post when they’re in stock.
vickers vanguard
CGN Regular
- Location
- Laval, Quebec
Great news...could you update this post when they’re in stock.
That barrel sleeve on the CSOR 11.6" gun should be standard on the 11.6" MRR if they use the same barrel profile.
The barrel of the 11.6" MRR barely has enough shoulder to support the crush washer. The sample in front of me has the crusher deformed because the shoulder is too narrow, the washer got squeezed into one side when torqued down. In fact, the inner diameter of the washer got squeezed out of the barrel and shaved off a bit.
This is dangerous, because if the crush washer is deformed too much and it is not longer round, it will be stuck under the muzzle thread! It is a major PITA to get a stuck crush washer like that out. it is also very marginal if the device needs to be timed with shims. The shims may deform.
The barrel of the 11.6" MRR barely has enough shoulder to support the crush washer. The sample in front of me has the crusher deformed because the shoulder is too narrow, the washer got squeezed into one side when torqued down. In fact, the inner diameter of the washer got squeezed out of the barrel and shaved off a bit.
This is dangerous, because if the crush washer is deformed too much and it is not longer round, it will be stuck under the muzzle thread! It is a major PITA to get a stuck crush washer like that out. it is also very marginal if the device needs to be timed with shims. The shims may deform.
Last edited:
