cz 858 foregrip keeps falling off while shooting

[Valentina]

So the fore grip on my 858 always falls off when I shoot... happened on the stock one so I bought after market one and still does it... seems like the pin that is supposed to keep it in does not.

Anyone else have this problem? Any recommendatio

 

[rally guy]

Never heard of that before

 

[icabod123]

Yeah, ever since I removed the bottom handguard, it moves and sometimes falls out when shooting. Try the NEA handguard lower - it is tight and the roll pin included with the kit is a perfect fit.

So the fore grip on my 858 always falls off when I shoot... happened on the stock one so I bought after market one and still does it... seems like the pin that is supposed to keep it in does not.

Anyone else have this problem? Any recommendatio

 

[bfiles]

All ya need is a new roll pin. Can easily be purchased at home depot. No need to stress.
Im may even have 1 I can give you. Ill check.

 

[paintgunner]

I found one for mine at NAPA.

 

[Leviathan024]

i have a csa rifle that is doing the same thing. it looks like the roll pin was never removed?

 

[Valentina]

I dont really see how a new roll pin will make a difference. The diameter of the new roll pin will be the same as the original one, but ill give it a shot.

NEA doesnt sell lower handguards for 858's anymore either I dont think.

 

[OldDirtyGatMasta]

You could try using some epoxy or something similar on the pin you already have.

Loctite or even nail polish might work to keep it in place.

 

[bfiles]

I dont really see how a new roll pin will make a difference. The diameter of the new roll pin will be the same as the original one, but ill give it a shot.

NEA doesnt sell lower handguards for 858's anymore either I dont think.

Push itbin and flare sides of it. Ive donebit with no problems after. Infact I gobthru more roll pins then most can imagine as I have 7 cz rifles and make wood sets with my buddy so they are always getting chqnge. Dont forget roll pins compress!!!!!

 

[bfiles]

CSA have solid roll pins. CZ has hollow ones

 

[paintgunner]

I dont really see how a new roll pin will make a difference. The diameter of the new roll pin will be the same as the original one, but ill give it a shot.

NEA doesnt sell lower handguards for 858's anymore either I dont think.

If its a roll pin you can carefully enlarge the end of it with a center punch. Just support the back side of the pin and give the other side a good hit, and repeat on the other side. The punch should spread the end of the pin just enough for it to stay in place.

 

[banditos]

Duct tape?

 

[bfiles]

Iwas just gonna say bondo???? LOL

 

[Leviathan024]

My issue seems like it is falling from the front. It is moving forward enough that the hook on the back is going over the roll pin?

 

[OldDirtyGatMasta]

My issue seems like it is falling from the front. It is moving forward enough that the hook on the back is going over the roll pin?

That's weird, I would think the U shaped part up front would be keeping it in place. Is your fore stock broken or morphed or something at the front?

 

[Leviathan024]

I think the U shaped part is loose and allows the handguard to move forward

 

[Lobster_pot]

My first cz858 I bought off the EE has the NEA lower hanguard on it permanently. It looks like somebody put epoxy on it. There's no way it's coming off. Doesn't bother me as I'm planning on leaving it on.

 

[superlative]

Just hammer the forward bracket with a rubber mallet.

 

[Valentina]

My issue seems like it is falling from the front. It is moving forward enough that the hook on the back is going over the roll pin?

Ya this is the same issue as with my CZ.

 

[Leviathan024]

Ya this is the same issue as with my CZ.

Great hopefully we can figure something out.