Dominion Arms 12.5" and 18.5 Barrel for Grizzly/Remington 870 Shotgun 79.99 $$$$
- Thread starter BoomSticKs
- Start date
Dantes Inferno
CGN Regular
I think the remington +2 is designed for an 18.5" barrel.
The Rem +2 will give a flush with muzzle look, but will only turn the gun into a 6+1, not a 7+1 as intended. Look at an S&J Hardware +2 instead.
Thanks for the infos.
Now I just need to confirm that the 18.5 will fit a regular 870 express!
Dantes Inferno
CGN Regular
Ya dude, your good to go. You should get the 12.5 as-well. I have 12.5" / 20" (and +3 ext.) / 26" Rib that I can change for whatever I'm doing. I doubt well see this kind of pricing again.
Also this looks about right for a rear site.
Also this looks about right for a rear site.
Thanks a lot Dantes!
I already have the 12.5 on my 870 with the S&J CQB stock and rail, which is flush with the feed tube and looks amazing, but I only wanted to be sure the fit of the 18.5 was the same as the 12.5.
For 80$, the 18.5 is a no brainer, I'll get it just in case I ever want to go hunting or shooting clays with my 870 (I'll have to thread it for chokes though).
I'll go order one right now!
I already have the 12.5 on my 870 with the S&J CQB stock and rail, which is flush with the feed tube and looks amazing, but I only wanted to be sure the fit of the 18.5 was the same as the 12.5.
For 80$, the 18.5 is a no brainer, I'll get it just in case I ever want to go hunting or shooting clays with my 870 (I'll have to thread it for chokes though).
I'll go order one right now!
Ya dude, your good to go. You should get the 12.5 as-well. I have 12.5" / 20" (and +3 ext.) / 26" Rib that I can change for whatever I'm doing. I doubt well see this kind of pricing again.
Also this looks about right for a rear site.
Dantes Inferno
CGN Regular
Try some reduced recoil loads and see how tight they pattern before threading for a choke, I saw some stuff recently that showed a 14" cyl. bore patterning as tight than a 22" barrel with a choke.
JustinF
Member
- Location
- st-lazare, qc
Spoke with Daniel Ryan via email about the chokes. Your website states that 18.5 grizzly are 12 gages 2 3/4 caliber
1300_stainless
Regular
- Location
- Nova Scotia, Canada
Have you done this? I ask because according to Canada Ammo they are brazed, which will take considerable heat to remove.
CanAm
Canada Ammo - CGN Sponsor
- Location
- Vancouver, BC
All the chmabers are 3" but the mags function best with 234
CanAm
Canada Ammo - CGN Sponsor
- Location
- Vancouver, BC
indeed
Cameron SS
CGN Ultra frequent flyer
- Location
- Ground Zero
SOLD OUT?!?!
Damnit, too slow. Getting any more, any time soon?
Damnit, too slow. Getting any more, any time soon?
Wormald1995
CGN Regular
- Location
- near toronto
Hopefully more become available, definitely interested in a 12.5 barrel.
demopeng
Regular
- Location
- GTHA Ontario
I received both the 12.5” and the 18.5” in the mail the other day. I must say, it’s a pleasant change from my 30” on my Super Magnum.
For those of you asking about the specifics of each barrel, hopefully I can clear some of the uncertainties up.
The 12.5” barrel is threaded for a choke. I believe they are “Win Chokes” but that is just what I remember being told on the phone, so take that with a grain of salt.
What I am positive about: It is stamped on the 12.5” barrel that it accepts 2 ¾ inch shells, in addition to 3 inch shells.
The 18.5” barrel is a fixed cylinder bore. The 18.5” barrel is stamped “for 2 ¾ inch shells only”. So I think it could be quite dangerous to jam a 3” shell into there and try and fire. If someone has done it, please chime in, and potentially include a link to your YouTube channel with a video of you firing a 3” shell out of this barrel that is designed ONLY for 2 ¾ inch shells.
For those of you asking about the specifics of each barrel, hopefully I can clear some of the uncertainties up.
The 12.5” barrel is threaded for a choke. I believe they are “Win Chokes” but that is just what I remember being told on the phone, so take that with a grain of salt.
What I am positive about: It is stamped on the 12.5” barrel that it accepts 2 ¾ inch shells, in addition to 3 inch shells.
The 18.5” barrel is a fixed cylinder bore. The 18.5” barrel is stamped “for 2 ¾ inch shells only”. So I think it could be quite dangerous to jam a 3” shell into there and try and fire. If someone has done it, please chime in, and potentially include a link to your YouTube channel with a video of you firing a 3” shell out of this barrel that is designed ONLY for 2 ¾ inch shells.
CanAm
Canada Ammo - CGN Sponsor
- Location
- Vancouver, BC
the 18.5" barrel has a 3" chamber, but as mentioned above, the gun uses 234, so the barrels are marked as such to reduce CS calls. You can verify by measuring against the other barrel
demopeng
Regular
- Location
- GTHA Ontario
popol
Regular
- Location
- chicoutimi, qc
Anymore 12.5 in coming in stock soon?? How soon?
Dantes Inferno
CGN Regular
The giant front sight was driving me nuts, and I didn't want to add a ghost ring rear sight to the gun so we made a bead sight for less than a dollar.
