Forend strap for 14" Norinco pump
- Thread starter geologist
- Start date
It shouldn't be to hard with a bit of drilling and maybe some dremmel work to recess the fastners.
You could use t-bolt hardware that comes in a few different styles.
Depending on how thick the foreend is where you want to mount the straps you might have to shorten the t bolts...Loctite and you will be good to go!
Here's an example of some T bolts. Post some pics. when you are done.
http://www.leevalley.com/hardware/page.aspx?c=1&cat=3,43576,52800,40361&p=40361
You could use t-bolt hardware that comes in a few different styles.
Depending on how thick the foreend is where you want to mount the straps you might have to shorten the t bolts...Loctite and you will be good to go!
Here's an example of some T bolts. Post some pics. when you are done.
http://www.leevalley.com/hardware/page.aspx?c=1&cat=3,43576,52800,40361&p=40361
Craftsman 441
CGN Regular
- Location
- Wainwright
geologist said:
Do you mean the forend with a strap around it to keep your hand from slipping?
Craftsman 441 said:
Yes, that's what I'm thinking about.
it keeps your hand from slipping off the forend and getting too close to the muzzle when you close the action.
Plus they look cool for the mall ninja in all of us!
I had my hand slip off the forend during a rapid fire session with slugs so I decided to put a strap onto Rosie O'Donnel's forend.
I made the loop wide enough so that I could use it with mitts on.
It took 15 minutes with a drill and dremel. If they don't find you handsome, they should at least find you handy.
I made the loop wide enough so that I could use it with mitts on.
It took 15 minutes with a drill and dremel. If they don't find you handsome, they should at least find you handy.
Last edited:
Strap looks good!
It would be nice if you could adjust the length to fit your hand/hand wear.
That fore end looks pretty slick as in not very grippy!
The speedfeed if you like plastic and hogue if you like rubber are my favorites...The wooden police ones are nice too
It would be nice if you could adjust the length to fit your hand/hand wear.
That fore end looks pretty slick as in not very grippy!
The speedfeed if you like plastic and hogue if you like rubber are my favorites...The wooden police ones are nice too
cantom said:
geologist detailed the building of (bleep) in this thread: http://www.canadiangunnutz.com/forum/showthread.php?t=136861The sights are Trak Lock, from Trijicon or Scattergun Technologies. (Front is epoxied over original. Rear requires two holes to be drilled and tapped.)
http://www.brownells.com/aspx/NS/store/productdetail.aspx?p=13162&s=
http://www.brownells.com/aspx/NS/store/productdetail.aspx?p=12522&s=
The +1 extension is Scattergun/Wilson Combat.
http://www.brownells.com/aspx/ns/store/ProductDetail.aspx?p=12526&title=EXTENDED+MAGAZINE+TUBE
Both are also available in
from The Shooting Edge. http://www.theshootingedge.com/Here is my attempt at it....
Stippled the fore end, you can see where the orange paint is where I cut it down. Made the strap with 1" buckles secured by kydex loops that were screwed in.
Looks kinda goofy but feels good.
Maybe that helps or gives you an idea.
J
Stippled the fore end, you can see where the orange paint is where I cut it down. Made the strap with 1" buckles secured by kydex loops that were screwed in.
Looks kinda goofy but feels good.
Maybe that helps or gives you an idea.
J
