fulll length resizing

Grey_Wolf said:
You don't have to full length size every time. Once you've got them back to factory spec then fired in your rifle you can use your neck sizer at the range for a few loads. You would still have to buy a press to use the f/l die unless you have a friend that would let you use theirs. As others have said you should get four or so loads before needing to f/l size again, watch the trim length too. I don't use bushings so can't help with that question
Click to expand...

yes. thank you Sir. this is what I expected. I really didnt want to have to pop for a press quite yet but I guess if Im in for a penny, Might as well be in for the pound...
Im on my second round on new cartridges. I have 50 that wont fit (range scrounge/ pickups). Once I get to the point where MY cartridges no longer fit, I will consider the press. OR as you say... see if one of the brothers at the range would be willing to squeeze them for me..
and yes.. all over case length like stink on a skunk!!
 
Mr. Jeffery said:
yes. thank you Sir. this is what I expected. I really didnt want to have to pop for a press quite yet but I guess if Im in for a penny, Might as well be in for the pound...
Im on my second round on new cartridges. I have 50 that wont fit (range scrounge/ pickups). Once I get to the point where MY cartridges no longer fit, I will consider the press. OR as you say... see if one of the brothers at the range would be willing to squeeze them for me..
and yes.. all over case length like stink on a skunk!!
Click to expand...

Watch the ee here or any other forum you frequent you may find a deal on a press. They come up from time to time at a reasonable price. I got mine (RCBS single stage) from my Dad who had bought it at a garage sale for cheap, you never know.
 
Mr. Jeffery said:
Thanks. will do.. yes.. you never know....

single stage??? whats that and I suppose theres a two stage or more? what that then?
Click to expand...

As opposed to the multi stage turret type like this h ttp://www.cabelas.ca/product/77040/lee-precision-classic-turret-press-kit
Single set h ttp://www.cabelas.ca/product/4574/rcbs-rock-chucker-supreme-press
mine is older and looks more like a C clamp and only has a single arm pivot rather than two. If you ask you will get ten different answers from ten different people as to which brand is better. I have only used RCBS and have never had an issue with it so don't feel the need to look elsewhere and would likely replace it with another if I had to get a new one.
 
Last edited:
I currently full length resize and trim for length every reload. Am I reducing the life of my brass and creating more work for myself? I don't crimp my necks on rifle rounds either, just my handgun loads. Is this something I should adopt?
 
Mr. Jeffery,
From some of the questions you have asked, it seems to me that you need to learn the basics of reloading. I would suggest that you get a reloading manual and read the front section-ignore the load data until you've read the how-to at the front of the book. This will answer most, if not all, of the questions you have asked on here. I'm not trying to be a d@#k, just trying to help you get started and not hurt yourself or anyone else.
The Wilson arbour press is designed for low pressure operations like neck sizing and bullet seating only. And, like you mentioned, portability. You need a bench mounted press to use full length resizing, bullet puller, and other kinds of reloading dies. You can get a press from Lee for about $100 that can do this for you. Or you can go hog wild and break the bank; like anything, if you get deep enough into it, the sky's the limit. If you full length re-size your range brass it should chamber in your rifle with no issues. Unless it was fired from an old military gun with a worn out chamber and then it's junk anyway. Full length sizing will help you determine this.

Good luck.
 
You must log in or register to reply here.
Back
Top Bottom