Modern Sporter builds Q&A
- Thread starter alberta tactical rifle
- Start date
ATRS Shaun
Business Member Rep.
- Location
- Calgary, AB
I have not tested that to confirm. As the hyperfire has an excessively large block of steel that sits on the safety, it is possible this could work, but it may also still be too large.
- Location
- Red Deer, Alberta
That is a Set of KNS extended pins. And there is ZERO / NONE / NO pins that will work with a hyperfire trigger (24C/Competition/Eclispe) with out modifying the trigger. Due to ATRS moving the rear pin forward a bit, it takes up the SAME space that is required by part of the rear spring support on those triggers. Short of taking a dremel or file to the hyperfire you will not get it to fit.
Me personally I gave up on the idea of putting a hyperfire 24C in my MS, and moved on, bought a different trigger for it. Which is too bad, the 24C was my favorite single stage trigger.
ATRS Shaun
Business Member Rep.
- Location
- Calgary, AB
Thanks Milemageman, I was hoping you'd chime in because I'm convinced you have the most experience trying to put a hyperfire into the MS.
- Location
- Red Deer, Alberta
I should correct myself.
It is not the pin that is in the way of the trigger, but the 'hook' on the upper that interferes with the Hiperfire 24C. You can install the Hiperfire 24C no problem in the lower, you just can't get a upper on. You'd have to modify the upper 'hook' by sliming it down or the rear of the spring support on the Hiperfire trigger or both. You'd need the rear sliding pin mod to have any hope of putting it together after modifying the upper hook and trigger. If it was a $130 Aero upper receiver, I'd have zero problems modifying and possibly destroying a upper in the process. But with a ATRS MS upper being $525 (or $625), huge backlog on getting a upper and the Hiperfire 24C being $330+ it could be a expensive experiment if it doesn't work. I just threw a Geissele National Match (required sliding rear pin mod) in my Hunting MS, a Trigger Tech Diamond in my Bench MS and I'll be putting a Geissele SSA-E in my Colt Canda MRR 'clone' training rifle. There are so many good trigger options out there for a AR style rifles, it's easier to find something else besides a Hiperfire 24C.
Hot damn! My MS is finally in my hands after 11 months of patience and day dreaming!!! I cannot get over the fit and finish. The thing is perfect! I’ll post pics later.
QUESTION.
For mags, will these options work?
http://www.bullseyelondon.com/magpu...6x45-magazine-10-round-pinned-to-5-black.html
http://www.bullseyelondon.com/magpu...6x45-magazine-20-round-pinned-to-5-black.html
QUESTION.
For mags, will these options work?
http://www.bullseyelondon.com/magpu...6x45-magazine-10-round-pinned-to-5-black.html
http://www.bullseyelondon.com/magpu...6x45-magazine-20-round-pinned-to-5-black.html
- Location
- Oakville, Ontario
Anyone have any experience with the hiperfire designated marksman ?
- Location
- Red Deer, Alberta
I know in my two MS lowers Magpul Gen M3 do not work. The over insertion tab hits the magwell before the magazine is seated.
Magpul MOE of Gen M2 work fine. Also the MFT's work fine as well.
Just ordered 2 of the LARS-15 mags. I didn’t know 10 rounds was legal in a semi auto?!
That's because they are pistol mags. Perfectly legal.
Some folks use their wifes clear nail polish to paint a protective layer over the writing on the mags stating what they are, and designed for.
If the writing stating it's a pistol mag rubs off then John Q. Law might have grounds to believe that it's a prohibited rifle magazine.
