My glock blew up

Status
Not open for further replies.
There is more than a little misinformation posted. Here are pictures of three variations of Glock barrels. Note, the Gen 1 was the worst of the three barrels as far as support is concerned. The Gen 3 and Gen 4 barrels are fully supported or as supported as any of my other guns.



I don't know what caused the case failure exhibited here. If there was no noticeable sound in the discharge then you can almost rule out a double charge though it is not uncommon in a 45acp or at least more easily to go unnoticed. Given the excitement caused by the gun coming apart the noise level increase might easily go unnoticed.

The only other explanation would be an out of battery discharge which is more likely the case given the condition of the case. I had a double charge in a 45acp case years ago and the case let go just above the case webbing but was not near as ruptured towards the case mouth. That was in a 1911. Grips cracked, four bullets in the mag burned off but did not fire in the normal sense of the word and all I got out of it was a blackened hand, a bent ego, and a lesson learned. The noise level was louder but not near twice as loud...just louder. The gun barrel was fine and that was with 10.2 gr of 231, assuming it was a full double charge.

Personally I would rule out a double charge but would not be surprised either if a lab tested the metalurgy and concluded it was. I and we just don;t know.

The case in the picture appears to have ruptured from the webbing to well up the case which would lead me to believe it occurred as a result of firing out of battery. I have no idea what caused that to happen. It could be the striker let go when the father put pressure on the trigger ahead of the slide closing, that might do it. The Glock design is pretty simple with few parts so one can imagine something letting go. Who knows?

Beavermeat - someone has told you something on the lines of detonation where gun where a couple of grains of pistol powder all of a sudden becomes a hand grenade or nuclear bomb due to "detonation". Smokeless powder burns it does not detonate. If you do some research you will find that industry labs have never been able to replicate this "detonation" event. Folks in the Cast Bullet Forum whom I have a great deal of respect for have concluded and confirm the same observation. My take on it is simply there just is not enough energy in a couple of grains of powder to destroy a modern firearm. Double the charge though and you are talking a whole different story.

Take Care

Bob
 
Nope.
glock-kb5.jpg
glockkboom.jpg
g21case2.jpg

Judging by the damage and primer being forced back into the firing pin hole, this was an over pressure issue. I don't see what this example has to do with the unsupported chamber?
 
Judging by the damage and primer being forced back into the firing pin hole, this was an over pressure issue. I don't see what this example has to do with the unsupported chamber?

...? I was answering a question about the fact that Glock has an unsupported chamber...the pics were for visual assistance. Never was it stated that the cause of this kaboom was an unsupported chamber.
As a matter of fact, I advised that he pull his rounds apart. So...I dunno what you're on about Dsiwy?
 
...? I was answering a question about the fact that Glock has an unsupported chamber...the pics were for visual assistance. Never was it stated that the cause of this kaboom was an unsupported chamber.
As a matter of fact, I advised that he pull his rounds apart. So...I dunno what you're on about Dsiwy?

I misinterpreter the intent of your pics my bad.
 
Another potential explanation: squib load on last shot left a bullet in the barrel. This round fired and excess pressure blew the case, and down into the magwell (as per Glock design). Any ring in the barrel?

If that were the case you would think there would be some barrel damage and at least one bullet lodged in the barrel. Most squibs I have witnessed leaves the squib case in the chamber or the case gets caught in the breach.

Take Care

Bob
 
That sentence doesn't make any sense. Blaming a pistol to fail because you screwed up your reloads is quite silly. And for the record, 1911 blows up too. Google 1911 kaboom.

I am not blaming the gun at all, but for me a polymere gun is more fragile to develop micro crack in the frame when using reload, that's only my opinion.

so if buy a Glock it will be brand new.
 
I am going to call them today too see where I can sent it and maybe how much for a new frame.
Does anyone know who does work for them in Canada?
 
Call Korth.

As it was a reload, it voids the warranty (as it would with every manufacturer), but Glock sometimes makes exceptions.

Regards.

Mark
 
Judging by the damage and primer being forced back into the firing pin hole, this was an over pressure issue. I don't see what this example has to do with the unsupported chamber?

It has a flattened primer also indicating an overpressure load. By the pictures this catastrophic failure is non other then an overpressure situation.
 
Roughly how many times had those cases been reloaded? I shoot 9 MM and my fired cases get a very close inspection every time they come out of the tumbler. Anything remotely suspect gets tossed. If I find more than a few in a batch of cleaned cases, they all get tossed. As others have suggested, looks like the pistol fired without fully being into battery, ie locked up.

I had this happen once in my Beretta CX-4 Carbine. Fortunately, neither me or the gun suffered any damage.

I have noticed some times when I size with my carbide dies, a ridge forms around the bottom of the case, maybe 2 MM up from the head. It means the empty case has probably been over loaded at some point or possibly just been reloaded too many times. If used, this ridge can prevent it from going into battery which is what I think happened in my CX-4 and it slam fired without the round being fully seated in the chamber. This was a big wake up call, hence my much more critical inspection of fired cases.

I am guilty I admit of using range brass that I don't know the history on.

I have noticed that brass fired out of a Glock, at least the 9 MM brass usually has a bit of a bulge in the lower part of the case body as some early gen Glock chambers don't fully encompass and support the whole cartridge. As a result I have found brass fired out of a Glock can be difficult to resize without my dies forming a ridge in the case near the case head. This ridge would cause the shell not to fully seat in a chamber.

Also, if your gun was not fully into battery when it fired, it suggests to me something was wrong with it as it should not have fired unless fully into battery.

Glad to hear no injuries other than to your gun.
 
Last edited:
I am not blaming the gun at all, but for me a polymere gun is more fragile to develop micro crack in the frame when using reload, that's only my opinion.

so if buy a Glock it will be brand new.

If you are suggesting reloads are tougher on a gun than factory rounds this is complete nonsense. Again, this is assuming the person doing the reloads is competent. Some people don't have the proper aptitude for reloading and would be safer to themselves and others by using factory ammo, not suggesting you or the OP are in this category.

I shoot a lot of 9 MM and my ammo is much more mild than any factory loaded 9 MM. When I do shoot some factory 9 MM, I am always amazed at how hot it is compared to my reloads, much more recoil and the empty cases are ejected well beyond my reloads.
 
Not kabooms but early ones had the same chamber issues, hence the "bulge buster" dies on the market.
I don't find a lot of it but when I do, it usually causes FTE's with my SR9. :p

Same here. I am guilty of using range brass and when they come out of my case cleaner and when I go to size I can tell pretty quickly if they were fired out of a Glock or not. I don't have a bulge buster die. When resizing an early gen Glock fired case in my carbide dies you can feel the resistance in the sizer die and if you force it, it will leave a ridge on the side of the case where it is in supported in the Glock. Any case showing this ridge is immediately scrapped as it is almost certain to hang up and not allow your pistol to go into battery.
 
The brass in question was once maybe twice fired. I also always look over the brass after tumbling looking for anything that may be an issue.
 
Status
Not open for further replies.
Back
Top Bottom