Precision/Sniper/Tactical
- Thread starter Farmboy
- Start date
My Remington 700 in 7MM Rem Mag
Sightron 8-32x56
MDT Tac 21 Long Action Chassis - Water Transfer Digital Snow Camo
Magpul PRS Stock
Magpul Rubber Stock Pad
Magpul Rubber Grip
Harris Bi-Pod
Magpul Front and Rear BUIS
Blue Force Rifle Sling
Sightron 8-32x56
MDT Tac 21 Long Action Chassis - Water Transfer Digital Snow Camo
Magpul PRS Stock
Magpul Rubber Stock Pad
Magpul Rubber Grip
Harris Bi-Pod
Magpul Front and Rear BUIS
Blue Force Rifle Sling
Last edited:
My Remington 700 in 7MM Rem Mag
Sightron 8-32x56
MDT Tac 21 Long Action Chassis - Water Transfer Digital Snow Camo
Magpul PRS Stock
Magpul Rubber Stock Pad
Magpul Rubber Grip
Harris Bi-Pod
Magpul Front and Rear BUIS
Blue Force Rifle Sling
my jaw just hit the floor, i have such a soft spot for digital snow camo... and to hydrodip the MDT... OMG
6.5x47L Surgeon 591R, Hart Heavy Palma barrel finished at 24", AICS, Jewell Trigger, NF ATACR, Spuhr Scope mount.
The target (red) is the first group of 5 after a few fouling shots sighting it in. Even my 14 y.o. son shot a .553" group (black target) with it!
The target (red) is the first group of 5 after a few fouling shots sighting it in. Even my 14 y.o. son shot a .553" group (black target) with it!
Attachments
Last edited:
Ashbury Chassis Mod-1 FDE, Bushnell Elite 3.5-21x50mm FFP HORUS TRMR2, LaRue SPR 34mm mount, Atlas Bipod, Surefire Brake, Remington 700 16.1 inch barrel/ oversized bolt handle installed/ OD Green custom finish/ Timney trigger, NF angle indicator. All work done by Casey at Tactical Ordnance.
gadget
Last edited:
The specs are:
Trued Rem 700 Action
PTG One Piece Bolt
PTG Recoil Lug
22" Kreiger 1in7" Twist Chambered in 223 Ackley (with a 0.088" freebore for 80gr bullets)
Jewel Trigger
Spuhr Mount
S&B PMII 12-50x56 (Goin to change to something smaller later)
Atlas Bi-Pod
I didn't drive an hour into the bush to let a thunderstorm get in the way of load development.
Howa 1500 Varmint .308
B&C Medalist A2 bedded w/ JB Weld. Tacpro cheek riser
EGW base, NF .885" Ultralite rings
NF NXS 8-32X56, Vortex bubble level
Magazine box removed to use the OE follower as a single shot, factory trigger adjusted light and crisp.
Howa 1500 Varmint .308
B&C Medalist A2 bedded w/ JB Weld. Tacpro cheek riser
EGW base, NF .885" Ultralite rings
NF NXS 8-32X56, Vortex bubble level
Magazine box removed to use the OE follower as a single shot, factory trigger adjusted light and crisp.
I didn't drive an hour into the bush to let a thunderstorm get in the way of load development.
Howa 1500 Varmint .308
B&C Medalist A2 bedded w/ JB Weld. Tacpro cheek riser
EGW base, NF .885" Ultralite rings
NF NXS 8-32X56, Vortex bubble level
Magazine box removed to use the OE follower as a single shot, factory trigger adjusted light and crisp.
I like that a lot! Very nice, how's it shooting for you?
Remington 700 MLR chambered in .338LM, shooting 270gr Lost River Ballistics (LRB) solid copper projectiles.
First shot on steel was a dead perfect bullseye, second shot, which was the one on video, was about 2.5" right, .5" low.
First shot on steel was a dead perfect bullseye, second shot, which was the one on video, was about 2.5" right, .5" low.
I only had time for a ladder test with handloads today but factory match ammo was sub moa when I did my part. We'll see how she goes but consistent 3/4 moa should be possible.
