Sticky : The CZ / Bolt action rimfire picture thread !

I wanted to wait until I got my scope mounted to officially join the club. Here's my new to me 452 Varmint 22wmr with Atlasworx bottom metal, DIP rail, and Bushell Elite 2.5-16x42. Crappy cell phone picture.

IMG_20160130_002215b_zpso7hraje6.jpg


Altasworx bottom metal.

IMG_20160130_012954a_zpslp2nqsgi.jpg
 
Last edited:
The 455 Canadian I ordered should be here tomorrow or the day after... unfortunately my rings got held up at the post office for "additional processing" (I though it was fine to order rings from the states?). I'll be sure to post a picture as soon as it's all together.
 
Some beautiful looking rifles!! Here is my new 455 Canadian 22LR with Nikon Prostaff 3-9x40 Matte BDC and bipod. Also sprang for two 25rd mags. Can't wait to try it out.

IMG_04591_zpsify8pnok.jpg

4e9e6c36-512b-40e7-9125-ff62dc7efafa_zpsti6tquo6.jpg
 
Here's a phone photo of my Canadian as promised, albeit late:
cpHflil.jpg


I've got BKL Std rings on there with a Nikon 3-9x40mm BDC scope.

It's my first gun and I've only taken it out shooting three times so far, but I'm doing alright; my groups are getting smaller and I'm getting more comfortable shooting left handed.
 
Zhanlin9426 said:
still cz452, anyone knows what is the finish on the receiver?
Click to expand...
Looks parkerized to me, and my untrained layman's eye.

I got a cz 455 off the ee a little bit ago. Never sighted it in yet. The super match with an american barrel on it, I think. I don't like the look of the stock much, but it seem to put my eye right where it should be with regards to the scope. Maybe because of my big head.
22lr
czrimfire_zpska8pmtad.jpg
 
Another CZ 452 American in .22lr with a Walnut stock.

It have pretty much all upgrades, steel trigger guard, Yodave Trigger, extended mag release, torx screws kit, aluminium magwell, etc...

This winter, I will try to find a nice vintage gloss Bausch & Lomb Balvar 2.5-10X40 scope for it.
Plan B is a gloss Leupold 3-9x33 EFR or a 2-7X28 scope.

UiOqRHb.png


Ln8C3b3.png


Zq9JkEE.png


qB0u35t.png


ikh4zFc.png


3rhWkVo.png


0iOrGWK.png


NnaXniN.png
 
Last edited:
Here is my other CZ 452, its a Varmint in .22LR

This rifle also have many upgrades like an Atlas aluminium trigger guard, +10% firing pin spring, Torx screws kit, aluminium magwell, Yodave trigger spring, Boyds stock and the extended mag release.

uDY97Jj.png


bHhOFug.png


jKjgN0h.png
 
Last edited:
lone-wolf said:
Nicely done photos
Click to expand...

Thanks !
I think its not bad for a cell phone camera.

Brocolt said:
interesting work on the Boyd's stock.
Click to expand...

There is much more work/rework involved in this stock...

The deepest part of the trigger guard was not enough deep, it was 1mm short.

The *Pocket* for the fromt barrel nut was also not enough deep.
I've done it deeper than it needed and I added shims untill it made contact with the barrel nut while the action is leveled/in contact with the stock on his entire length.

The shape of the stock was not the same on both sides.

Finish had some flaws.

etc,etc...

I had to spend many hours fixing everything, lets hope the rifle will shoot well in this stock #fingercrossed ! :p
 
Last edited:
You must log in or register to reply here.
Back
Top Bottom