The "What Have You Reloaded Today" thread

Test loads for a Savage 99A / .250-3000 /20" carbine with as it should have been from inception 1-10 twist and 100gr bullets/Win 760 Fed mag primers..............loaded down a couple or three grains lighter than those used in my classic Rem 700...........Harold
 
Loaded 2 boxes of 20 - 300 Win Mag 180 gr Nosler Accubond for my son .He put a new scope on his Tikka and is going to the range today. Raining today this afternoon I will be loading for my pistols.
 
Made up a batch of .17 Rem (25gr VMax, Varget) and .375 Ruger (260gr AB, RL15).

It sure felt strange going from the tiny .17 to the much larger .375 case/bullets.
 
Since the 10 of April when I finished annealing 69 lbs of .308 Lapua brass, I have resized and weight sorted all of them into 1 gr batches. I have ended up with a large batch weighing 170.0-170.9 gr, a larger batch of 173.0-173.9 gr. Smaller batches in the 171 gr, 172 gr and 174 gr range. Since I have the largest amount of 173 gr brass, I will use this, once sorted into 1/2 batches for match ammo. The rest will be used for practice. Should last me a couple years.
 
i reloaded 10, 32 H&R mag's ( that's all the brass i have right now) i don't have dies yet either but i had 10 new unfired brass, so i loaded them with 2.5gr of titegroup and a 95gr bullet and im going to try them in my 1918 lithgow No1mkIII* in about 5 minutes (i also made a barrel liner and chambered it for 32 hr mag and silver soldered it into the bored out Lee Enfield barrel today too)
 
Reloaded 300rnds of 9mm. 124/125gr of XMetal pills behind 3.6gr Titegroup at 1.07" Also finally got around and tumbled about 2K pieces of 9mm brass. Arghh.
 
Reloaded my last 350rnds 9mm using 125gr XMetal pills behind 3.6gr Titegroup.

Reloaded 200rnds 9mm using 124gr Campros behind 4.0gr Titegroup. Need to chrony 'em to ensure they make IPSC minor power factor. From what I've read, 4gr TG behind a 124gr pill should do it out of a 5" barrel with some wiggle room. Used to shoot 4.1gr TG out of my Glock (4.5" barrel) which came up to an average 135 PF.

Reloaded 100rnds 45LC using 250gr Campros behind 6.8gr Unique.

Got some IMR 700x so decided to make up some test 45LC test loads using 250gr Campros. 10rnds with 4.6gr, 10rnds with 4.8gr and 10rnds with 5gr 700x.

Humm, does 700x meter well for everyone? I found one powder drop will be 4.6gr, next will jump to 4.9gr, next will be 4.8gr, back to 4.6gr etc. Basically had to check each drop. This on my Hornady LNL AP. I'll give it a try on my RCBS powder meter next time and see if it's the same issue.
 
Loaded for a Savage 99A 250/3000 1-10 twist ,some with Win 760 ,RE#15 + IMR 3031 under a 100gr Sierra SP /Rem brass fed mag primer. The gun did not like the 100gr Hornady but put several 75gr Sierra HP's in a cloverleaf.Need a deer bullet and can't load this one as warm as my Rem 700 Classic......this is a little 20" carbine so should be nice to push bush with and snipe from my tree stand at woods ranges......Harold
 
Reloaded my first 100 round batch of 9mm using 124gr Campro FCP RN behind 3.9gr of Titegroup.

Also made up a wooden reloading block for the 9mm
 
Reloaded 600rnds of Campro 9mm 124gr behind 4.0gr of Titegroup. Good lord, how S&B brass can slow down your reloading sessions. ARGH!

Temps said:
Reloaded my first 100 round batch of 9mm using 124gr Campro FCP RN behind 3.9gr of Titegroup.
Click to expand...

Does 3.9gr Titegroup behing 124gr pill meet minor PF?
 
You must log in or register to reply here.
Back
Top Bottom