**TYPE 81 7.62X39 SERVICE RIFLE** ~Now on the way~ -Last chance!

Status
Not open for further replies.
Wow, I love everyone jumping off the TI bandwagon realizing their customer non service is garbage. just tell people the truth, its much easier than lying and trying to make sure you tell the same crap.
 
Jaylegger said:
There was some discussion earlier with pcvando, some info he received from TI indicated the barrel was only about .75 inches longer than the restricted barrel based on the reasons you cite. If that were the case the bayonet should have been very close to fitting properly with, instead of, the bayo ring resting near the front front of the barrel it would have rested close to the rear ring on the muzzle. Doesn't look like this is the case however. bummer.

I know Dilligaf is planning on lengthening the tang of the bayo and then fabricate longer scales but I think I'll just purchase a lug extension to compensate.

Something like this. But then again I really don't see a use for any of this except for a photo op maybe.

https://www.apgdefense.com/product-page/bayonet-lug-extender
Click to expand...

The barrel assembly is only .75 inches longer. The barrel is actually 1.4 inches longer or so but hides further into the grenade launcher muzzle device which slides over the barrel.

Barrel. Vs barrel plus grenade launcher sleeve. Think fake suppressor over barrel inside fake suppressor.
 
DILLIGAF said:
Looks like an easy fix. I cant start my Bayo project.

Does it at least lock on the bayo lug ?
Click to expand...

Does the bayo blade run all the way through to where it locks into the lug? In other words, is there metal all the way through or is it two metal parts connected by the handle? Obviously I have yet to grab one but extending the handle would be a fairly easy mod. It would change the look a bit but still lock up and extend past the muzzle properly.
 
Jladdy said:
Wow, I love everyone jumping off the TI bandwagon realizing their customer non service is garbage. just tell people the truth, its much easier than lying and trying to make sure you tell the same crap.
Click to expand...

I dunno.
I had a problem with my Skorpion and they had the right part out quickly.
 
fenceline said:
The barrel assembly is only .75 inches longer. The barrel is actually 1.4 inches longer or so but hides further into the grenade launcher muzzle device which slides over the barrel.

Barrel. Vs barrel plus grenade launcher sleeve. Think fake suppressor over barrel inside fake suppressor.
Click to expand...

The relationship between the bayo lug and the launcher muzzle device/barrel should have theoretically meant the bayo would still fit without mods but just not exactly on the front muzzle as the original but just 3/4" back on the rear ring of the front muzzle. Something must be off here, either the barrel isn't as far into the launcher sleeve ass previously indicated or the bayo lug is back a little further. Difficult to say which.
 
Jaylegger said:
The relationship between the bayo lug and the launcher muzzle device/barrel should have theoretically meant the bayo would still fit without mods but just not exactly on the front muzzle as the original but just 3/4" back on the rear ring of the front muzzle. Something must be off here, either the barrel isn't as far into the launcher sleeve ass previously indicated or the bayo lug is back a little further. Difficult to say which.
Click to expand...

Barrel measurements on restricted vs non restricted are taken from the frt entry. The difference in length is taken from TI comments regarding oal.
 
fenceline said:
Barrel measurements on restricted vs non restricted are taken from the frt entry. The difference in length is taken from TI comments regarding oal.
Click to expand...

Agree, that's pretty much what pcvando stated as well and what I was basing my calculations on. Perhaps my calculation were off but I tripled checked over the course of a couple weeks. Anyways it is what it is, the bayo ring will not line up with the front muzzle without mods.
 
Jladdy said:
Wow, I love everyone jumping off the TI bandwagon realizing their customer non service is garbage. just tell people the truth, its much easier than lying and trying to make sure you tell the same crap.
Click to expand...

LOL what?

Definition of the word "lie" : an intentionally false statement.

Now enlighten us ; what lies were told?

Youza.
 
Well, i was sceptical that these rifles would ever show up, but last week I decided to order one and I got shipping confirmation today! Stoked to try it out, hopefully they get in some more mags soon as I want about 10 or 15. :)
 
Gatehouse said:
Well, i was sceptical that these rifles would ever show up, but last week I decided to order one and I got shipping confirmation today! Stoked to try it out, hopefully they get in some more mags soon as I want about 10 or 15. :)
Click to expand...

That's just fvcking great. So happy for you. lol.
 
Gatehouse said:
Well, i was sceptical that these rifles would ever show up, but last week I decided to order one and I got shipping confirmation today! Stoked to try it out, hopefully they get in some more mags soon as I want about 10 or 15. :)
Click to expand...

I was kind of kidding about the last in first out shipping method.. I quess I was really right..
that sucks I might not see mine till Dec.
 
GUB said:
I was kind of kidding about the last in first out shipping method.. I quess I was really right..
that sucks I might not see mine till Dec.
Click to expand...

Real kick in the nuts isn't it. Pay a year and a half ago and then watch as people who naysayed and doubted jump on at the end and get them first.

It's even worse when you know they are a short 20 min drive away. And pick up isn't an option.
 
Status
Not open for further replies.
Back
Top Bottom