Right? For the money it's a really great addition to my safe and definitely coming out camping with my from now on.
NEW Kel-Tec GEN 2 Sub 2000
- Thread starter reliablegun
- Start date
Right? For the money it's a really great addition to my safe and definitely coming out camping with my from now on.
jordanmalmal
Regular
- Location
- Ontario
I really loved mine, but it shot gas in my face when shooting left handed.
I wonder if they did anything to change that?
I wonder if they did anything to change that?
strikerfire
New member
- Location
- GTA
I shoot the G2 left handed, the new adjustable 3 position butt plate and higher sight radius help not get gas and shells in the face.
jordanmalmal
Regular
- Location
- Ontario
Do you pull the buttstock closer to the ejection port? It looks as if the buffer tube only reaches as far as the Gen 1.
I would def be in for another sub2000, but I sold my last one due to the ejection in the face problem.
strikerfire
New member
- Location
- GTA
With the Gen 2 extended to the maximum position, it is slightly longer than a gen 1 with the butt extension attached. I had the same issue with my gen 1 before I added a butt extension. I put 100 rounds through it today and it shot great.
- Location
- Toronto, Ontario
Did you have to disable comments to stop the rabid anti-gun windbags?
GundamZero
CGN frequent flyer
- Location
- Toronto
anymore coming in?
LeadMonkey
CGN frequent flyer
- Location
- Off The Radar
That pretty much sums it up... Plus I don't monitor youtube very often... was more of a sneak peak for CGNers! Hope to post a range report soon!
K-Roc
CGN Ultra frequent flyer
- Location
- Outer Ottawa
Think I will buy the Beretta version the second it lands...
shadowz
New member
- Location
- Toronto (GTA)
anymore coming in? When ? Which versions?
Would love a sig226 version ASAP
Thanks
Would love a sig226 version ASAP
Thanks
Definitely more ordered! No current ETA on the Sig or Beretta Version. Kel-Tec is running full tilt in producing these already.
Any concrete news and I'll post it for you guys.
Nick
st1264
CGN Ultra frequent flyer
- Location
- Windsor ON
If definite 'stock incoming' info would be available, I'd put a deposit on a Sig 226 version to secure it.
Doubt Kel-Tec can make these fast enough for demand.
More have just landed, will be made available for purchase tomorrow.
New 2016 price is $719.99
New 2016 price is $719.99
bcbravo2zero
CGN Regular
Very much looking forward to the s&w model
Last edited:
cmoney
Regular
- Location
- Invermere, BC
link goes to a lot of nice firearms but no Sub 2000 gen 2 on there yet.
GundamZero
CGN frequent flyer
- Location
- Toronto
Maybe already sold out.
cmoney
Regular
- Location
- Invermere, BC
Maybe
pisces-guy
CGN frequent flyer
- Location
- West Kelowna, B.C.
I`ve got one, they`re great guns and no reliability issues...did a couple of mods though. A fully loaded mag drops out of the mag well just fine, but an empty one doesn`t. I got some 800 grit sandpaper and worked the mag over with that for about ten minutes...no more issues. Also sanded a few sharp points on the plastic that tended to grab on to my clothes...five minutes.
I then replaced the front sight pin with a Trijicon iridium night sight, to improve it`s low light ability...took five minutes. Dismantled the gun and used the 800 grit paper to lightly sand dry, then with G96, the bolt assembly... It`s painted black from the factory and makes racking the action a bit stiff, after the light sanding and lubing with G96, it was smooth as silk. I took it out shooting at that point, and it shoots well, with no malfunctions...but it would be even more accurate if the trigger was lighter and a bit crisper. It`s currently at my gunsmith`s, getting that trigger re-cut and lightened, and I`ll give you guys a full report when I get it back from them. All in all, a well made, fun gun...with a few minor quirks to fix to make it a great little gun.
I then replaced the front sight pin with a Trijicon iridium night sight, to improve it`s low light ability...took five minutes. Dismantled the gun and used the 800 grit paper to lightly sand dry, then with G96, the bolt assembly... It`s painted black from the factory and makes racking the action a bit stiff, after the light sanding and lubing with G96, it was smooth as silk. I took it out shooting at that point, and it shoots well, with no malfunctions...but it would be even more accurate if the trigger was lighter and a bit crisper. It`s currently at my gunsmith`s, getting that trigger re-cut and lightened, and I`ll give you guys a full report when I get it back from them. All in all, a well made, fun gun...with a few minor quirks to fix to make it a great little gun.
Bingo, yes they were online for a while but sold out quickly.
Give us a call at the shop if you're interested in one.
Regards,
Reliable
