PDW builds - Lets see them, and share results

agilent_one said:
CCS Stock for my 9" 300BLK finally arrived:

From:
300blk.jpg


To:
ccs1_zpsc94aa47a.jpg
Click to expand...



Beautiful gun.

Now shoot it! Today! Let us know how it functions!

MG
 
Final configuration... made a few adjustments, mainly ditching the optic and folding Iron sights for the Centurion Arms Diopters and the VFG for the Magpul AVG...and a B.A.D. lever.

stuff004.jpg


And the Vortex Razor Red dot works reeeeeal good on my TP-9!

stuff014.jpg


Cheers all!
 
20130507_181300_zps488a4450.jpg


NEA 10.5
Magpul tan stock
Dpms carbine buffer tube...
Ambi sling plate
Jp spring kit
Magpul rail sling mount
Magpul plastic sights (airsoft mp)
Gas pedal
Effin A comp
Pmag
Ergo tan grip
Eotech x2 something? The reticle has two small dots and the large circle.
 
Last edited:
OK so just like TV-PressPass did - from the ashes this topic rises yet again with some cool lookin pics !!!!

RRA AR15 9mm 7.5" - MagPul hardware.

Its not done. The Aimpoint is airs h i t and is there for mock up only. Trying to decide if I should go with a real H1 or a EOTech XPS2-2 Holographic ... I may also adapt a Noveske KX3 (Flaming Pig) on the front, I say adapt becuz they only come in a 1/2 x28 thread. Would need to retap to 1/2 x 36.

Anybody try this on a 9mm AR PDW yet ?





Here it is beside a CAR 15 build - size is very similar.




With the carbines ..
 
Last edited:
sendmorebrains said:
OK so just like Kevin M did - from the ashes this topic rises yet again with some cool lookin pics !!!!

RRA AR15 9mm 7.5" - MagPul hardware.

Its not done. The Aimpoint is airs h i t and is there for mock up only. Trying to decide if I should go with a real H1 or a EOTech XPS2-2 Holographic ... I may also adapt a Noveske KX3 (Flaming Pig) on the front, I say adapt becuz they only come in a 1/2 x28 thread. Would need to retap to 1/2 x 36.

Anybody try this on a 9mm AR PDW yet ?





Here it is beside a CAR 15 build - size is very similar.




With the carbines ..
Click to expand...
Awesome! I've wanted to build a 9mm AR for a while now. Where did you get those mags? I was thinking of building one with glock mags to as they are readily available (and 10 rounds).
 
sendmorebrains said:
OK so just like TV-PressPass did - from the ashes this topic rises yet again with some cool lookin pics !!!!

RRA AR15 9mm 7.5" - MagPul hardware.

Its not done. The Aimpoint is airs h i t and is there for mock up only. Trying to decide if I should go with a real H1 or a EOTech XPS2-2 Holographic ... I may also adapt a Noveske KX3 (Flaming Pig) on the front, I say adapt becuz they only come in a 1/2 x28 thread. Would need to retap to 1/2 x 36.

Anybody try this on a 9mm AR PDW yet ?






I found a top end on CGN with a 5" barrel , I believe it to be an ATR Barrel so it is 5/8 x24 TPI .I found the barrel so short that it felt like your fingers could slip over the end, as well as the angled fore grip stuck out to far and looked stupid. So I built on the lathe out of aluminum , we will see how long it holds up. If I ever get to the range enough to torture test it. I am sure you could drill the flaming pig and re tap it but the 1/2 x 36 thread taps are stupid expensive, I think they quoted me $146.00 at the machine tool place.
I wanted to build a fake can for the 16" upper on the colt but figured a way around it , I built a sleeve for the barrel that comes back to the front sight post, then the tube fit over that with a pocket for the flash suppressor, this way there is no gas allowed back into the canister. Makes it look like a 12" with a silencer.




Click to expand...
 
Noveske KX3 (Flaming Pig) on the front, I say adapt becuz they only come in a 1/2 x28 thread. Would need to retap to 1/2 x 36.

Anybody try this on a 9mm AR PDW yet ?
Click to expand...

No because it won't work. You can't retap 28 tip thread to 36 tip thread of the same size without buggering up both. The only solution is to cut off the existing muzzle thread and recut new 1/2-28 thread along with a new crown. Either that or have a conversion sleeve/extension made.
 
Suputin said:
The only solution is to cut off the existing muzzle thread and recut new 1/2-28 thread along with a new crown. Ei
Click to expand...

Which as you already know is then creating a prohibited device. We have had this discussion before. You are NOT legally allowed to cut down the barrel on an AR15 style firearm. I don't like that bit of law either but to encourage someone into breaking the law??????
 
You must log in or register to reply here.
Back
Top Bottom