Does this count? Dlask 8.5 bbl, custom Butler creek folder, restricted unless the stock is pinned, then she sits @ 26 1/2".
Hical,
do ya have any of those Butler Creek folding stocks in stock??????
Tactical Rimfire Picture Thread! S&W M&P 15-22/Colt M4 Ops/Ruger SR-22/Rem 597 VTR...
- Thread starter the_drewster19
- Start date
Hical,
do ya have any of those Butler Creek folding stocks in stock??????
Thanks, was really just farting around, took about 50 pics to actually get a couple I thought were decent.
Cheers
Non-Restricted Goodness!
Finally got the latest toy sighted in and I am quite happy with it. Very fun!
I sighted her in for 50m and am very happy with the accuracy.
Sitting at the bench, I was putting all my shots (50+ rnds) in an area the size of my hand on a small target out at 100m. At 50m it was half that size. At 25m (where I could actually see my target properly) I was putting all shots in an area the size of a Loonie ; again I wasn't firing off three rounds then announcing my group size, I was literally putting a minimum of 50 rounds into each targets
.
I am confident with a nice scope this rifle would be incredibly accurate.
However, for me it's just a fun plinker that is heavy enough as is. The only thing missing is the GSG 110rnd drum. I can hardly wait.
It's as reliable as the ammunition I am using. I had only one Failure-To-Fire due to missing primer (I attempted to fire it a few times) out of a brick of 400 American Eagle 38gr HP rounds.
Enough, here she is:
If anyone cares, it all started with a Ruger SR-22... I then added the following:
Dlask 12.5" .920" Bull barrel
Dlask .920" Barrel support block
Dlask .920" Thread protector
Dlask Full length rail
Dlask Adjustable V-block
Dlask Hex hold down bolt
Magpul MOE grip (FG)
Magpul MOE stock (FG - Milspec)
Magpul GEN2 MBUS (FG - front and rear)
Magpul ASAP
Volquartsen Recoil buffer
Volquartsen Automatic bolt release
Volquartsen Exact edge extractor
~Cheers
Finally got the latest toy sighted in and I am quite happy with it. Very fun!
I sighted her in for 50m and am very happy with the accuracy.
Sitting at the bench, I was putting all my shots (50+ rnds) in an area the size of my hand on a small target out at 100m. At 50m it was half that size. At 25m (where I could actually see my target properly) I was putting all shots in an area the size of a Loonie ; again I wasn't firing off three rounds then announcing my group size, I was literally putting a minimum of 50 rounds into each targets
. I am confident with a nice scope this rifle would be incredibly accurate.
However, for me it's just a fun plinker that is heavy enough as is. The only thing missing is the GSG 110rnd drum. I can hardly wait.
It's as reliable as the ammunition I am using. I had only one Failure-To-Fire due to missing primer (I attempted to fire it a few times) out of a brick of 400 American Eagle 38gr HP rounds.
Enough, here she is:
If anyone cares, it all started with a Ruger SR-22... I then added the following:
Dlask 12.5" .920" Bull barrel
Dlask .920" Barrel support block
Dlask .920" Thread protector
Dlask Full length rail
Dlask Adjustable V-block
Dlask Hex hold down bolt
Magpul MOE grip (FG)
Magpul MOE stock (FG - Milspec)
Magpul GEN2 MBUS (FG - front and rear)
Magpul ASAP
Volquartsen Recoil buffer
Volquartsen Automatic bolt release
Volquartsen Exact edge extractor
~Cheers
the drewster19,
please explain just alittle better if you may how in the hell did you apply the crayon finish on your m&p??
Sharpen the crayon?? What did you use to take the extra crayon off, etc...
Thanks
please explain just alittle better if you may how in the hell did you apply the crayon finish on your m&p??
Sharpen the crayon?? What did you use to take the extra crayon off, etc...
Thanks
DeltaDevil
Member
Hmmm...
Been a while since we have updated this thread.
I will add my SR-22, created as an homage to jt's sweet SR he had going (also, his was the one that convinced me I needed one!
What are the side rails I see on your sr22 ? Is the forestock the factory one ?
As purchased forestock with a set of Dlask rails, and Magpul XTG rail covers (I kinda miss-counted or miss-measured so I am kinda short on those, already ordered more from Wolverine along with some flip up sights.
I also have a Tuffer buffer inside, along with a Marauder/Nomad mag release and bolt hold open mod. Allows me to use the Nomad mags with no permanent mag mods, plus I like the look of the extended mag release!
heres my newly acquired 10/22 Nomad/Marauder! Check out the scope! i found it at my local gun place, it's got a blue lit reticle, and is 3-10x zoom.... fits the rifle good! Im looking for side rails, and have ordered an angle foregrip, and will replace the bipod with the verticle grip/bipod. I also converted an airsoft mag and stock 10/22 mag.Im also getting a different barrel, and going with an airsoft quick detach suppressor. there are a few mods planned.. Dang this thing is fun!
